- 您现在的位置：买卖IC网 > PDF目录20640 > ADE7753ARSZ (Analog Devices Inc)IC ENERGY METERING 1PHASE 20SSOP PDF资料下载
参数资料
| 型号： | ADE7753ARSZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 21/60页 |
| 文件大小： | 0K |
| 描述： | IC ENERGY METERING 1PHASE 20SSOP |
| 标准包装： | 66 |
| 输入阻抗： | 390 千欧 |
| 测量误差： | 0.1% |
| 电压 - 高输入/输出： | 2.4V |
| 电压 - 低输入/输出： | 0.8V |
| 电流 - 电源： | 3mA |
| 电源电压： | 4.75 V ~ 5.25 V |
| 测量仪表类型： | 单相 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 20-SSOP |
| 包装： | 管件 |
| 产品目录页面： | 797 (CN2011-ZH PDF) |
| 配用： | EVAL-ADE7753ZEB-ND - BOARD EVALUATION AD7753 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页
ADE7753
ADE7753 INTERRUPTS
ADE7753 interrupts are managed through the interrupt status
register (STATUS[15:0]) and the interrupt enable register
(IRQEN[15:0]). When an interrupt event occurs in the ADE7753,
the corresponding flag in the status register is set to Logic 1—
see the Interrupt Status Register section. If the enable bit for this
interrupt in the interrupt enable register is Logic 1, then the
IRQ logic output goes active low. The flag bits in the status
register are set irrespective of the state of the enable bits.
To determine the source of the interrupt, the system master
(MCU) should perform a read from the status register with
reset (RSTSTATUS[15:0]). This is achieved by carrying out a
read from Address 0x0C. The IRQ output goes logic high on
completion of the interrupt status register read command—see
the Interrupt Timing section. When carrying out a read with
reset, the ADE7753 is designed to ensure that no interrupt
events are missed. If an interrupt event occurs just as the status
register is being read, the event is not lost and the IRQ logic
output is guaranteed to go high for the duration of the interrupt
status register data transfer before going logic low again to
indicate the pending interrupt. See the next section for a more
detailed description.
Using the ADE7753 Interrupts with an MCU
tation of ADE7753 interrupt management using an MCU. At
time t 1 , the IRQ line goes active low indicating that one or more
interrupt events have occurred in the ADE7753. The IRQ logic
output should be tied to a negative edge-triggered external
interrupt on the MCU. On detection of the negative edge, the
MCU should be configured to start executing its interrupt
service routine (ISR). On entering the ISR, all interrupts should
be disabled by using the global interrupt enable bit. At this
point, the MCU external interrupt flag can be cleared to capture
interrupt events that occur during the current ISR. When the
MCU interrupt flag is cleared, a read from the status register
with reset is carried out. This causes the IRQ line to be reset
logic high (t 2 )—see the Interrupt Timing section. The status
register contents are used to determine the source of the
interrupt(s) and therefore the appropriate action to be taken. If
a subsequent interrupt event occurs during the ISR, that event is
recorded by the MCU external interrupt flag being set again
(t 3 ). On returning from the ISR, the global interrupt mask is
cleared (same instruction cycle), and the external interrupt flag
causes the MCU to jump to its ISR once a gain. This ensures
that the MCU does not miss any external interrupts.
MCU
INTERRUPT
t 1
t 2
t 3
FLAG SET
IRQ
MCU
PROGRAM
SEQUENCE
JUMP
TO
ISR
GLOBAL
INTERRUPT
MASK SET
CLEAR MCU
INTERRUPT
FLAG
READ
STATUS WITH
RESET (0x05)
ISR ACTION
(BASED ON STATUS CONTENTS)
ISR RETURN
GLOBAL INTERRUPT
MASK RESET
JUMP
TO
ISR
02875-0-044
Figure 45. ADE7753 Interrupt Management
CS
t 1
SCLK
t 9
DIN
0
0
0
0
0
1
0
1
t 11
t 11
DOUT
DB7
DB0 DB7
DB 0
READ STATUS REGISTER COMMAND
STATUS REGISTER CONTENTS
IRQ
02875-0-045
Figure 46. ADE7753 Interrupt Timing
Rev. C | Page 21 of 60
相关PDF资料 |
PDF描述 |
|---|---|
| A7SSB-1506G | CABLE D-SUB-AFM15B/AE15G/AFM15B |
| HMM06DSUS | CONN EDGECARD 12POS .156 DIP SLD |
| GCC10DCAI-S189 | CONN EDGECARD 20POS R/A .100 SLD |
| ADE7759ARSZ | IC ENERGY METERING 1PHASE 20SSOP |
| RMM40DTAD-S189 | CONN EDGECARD 80POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADE7753ARSZ | 制造商:Analog Devices 功能描述:ENERGY METERING IC |
| ADE7753ARSZ | 制造商:Analog Devices 功能描述:IC MULTIFUNCTION METER |
| ADE7753ARSZRL | 功能描述:IC ENERGY METERING 1PHASE 20SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:* |
| ADE7753-ARSZRL | 制造商:Analog Devices 功能描述: |
| ADE7753XRS | 制造商:Analog Devices 功能描述: |
发布紧急采购，3分钟左右您将得到回复。