参数资料
型号: ADSP-TS203SABP-050
厂商: Analog Devices Inc
文件页数: 11/48页
文件大小: 0K
描述: IC DSP FLOAT/FIXED 500MHZ 576BGA
标准包装: 1
系列: TigerSHARC®
类型: 定点/浮点
接口: 主机接口,连接端口,多处理器
时钟速率: 500MHz
非易失内存: 外部
芯片上RAM: 512kB
电压 - 输入/输出: 2.50V
电压 - 核心: 1.05V
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 576-BBGA 裸露焊盘
供应商设备封装: 576-BGA-ED(25x25)
包装: 托盘
其它名称: ADSP-TS203SABP050
ADSP-TS203SABP050-ND
Rev. D
|
Page 19 of 48
|
May 2012
When default configuration is used, no external resistor is
needed on the strap pins. To apply other configurations, a 500 Ω
resistor connected to VDD_IO is required. If providing external
pull-downs, do not strap these pins directly to VSS; the strap
pins require 500 Ω resistor straps.
All strap pins are sampled on the rising edge of RST_IN (deas-
sertion edge). Each pin latches the strapped pin state (state of
the strap pin at the rising edge of RST_IN). Shortly after deas-
sertion of RST_IN, these pins are reconfigured to their normal
functionality.
These strap pins have an internal pull-down resistor, pull-up
resistor, or no-resistor (three-state) on each pin. The resistor
type, which is connected to the I/O pad, depends on whether
RST_IN is active (low) or if RST_IN is deasserted (high).
Table 17 shows the resistors that are enabled during active reset
and during normal operation.
SYS_REG_WE
I (pd_0)
BUSLOCK
SYSCON and SDRCON Write Enable.
0 = one-time writable after reset (default)
1 = always writable
TM1
I (pu)
L1BCMPO
Test Mode 1. Do not overdrive default value during reset.
TM2
I (pu)
TM2
Test Mode 2. Do not overdrive default value during reset.
TM3
I (pu)
TM3
Test Mode 3. Do not overdrive default value during reset.
Table 16. Pin Definitions—I/O Strap Pins (Continued)
Signal
Type (at
Reset)
On Pin …
Description
I = input; A = asynchronous; O = output; OD = open-drain output; T = three-state; P = power supply; G = ground; pd = internal pull-down
5kΩ; pu = internal pull-up 5 kΩ; pd_0 = internal pull-down 5 kΩ on processor ID = 0; pu_0 = internal pull-up 5 kΩ on processor ID = 0;
pu_od_0 = internal pull-up 500 Ω on processor ID = 0; pd_m = internal pull-down 5 kΩ on processor bus master; pu_m = internal pull-up
5 kΩ on processor bus master; pu_ad = internal pull-up 40 kΩ. For more pull-down and pull-up information, see Electrical Characteristics
Table 17. Strap Pin Internal Resistors—Active Reset
(RST_IN = 0) vs. Normal Operation (RST_IN = 1)
Pin
RST_IN = 0
RST_IN = 1
BMS
(pd_0)
(pu_0)
BM
(pd)
Driven
TMR0E
(pd)
Driven
BUSLOCK
(pd_0)
(pu_0)
L1BCMPO
(pu)
Driven
TM2
(pu)
Driven
TM3
(pu)
Driven
pd = internal pull-down 5 kΩ; pu = internal pull-up 5 kΩ;
pd_0 = internal pull-down 5 kΩ on processor ID = 0;
pu_0 = internal pull-up 5 kΩ on processor ID = 0
相关PDF资料
PDF描述
ADUC7021BCPZ62-RL7 IC MCU 12BIT 1MSPS UART 40-LFCSP
ADUC7023BCPZ62I-R7 IC MCU 12BIT 62KB FLASH 32LFCSP
ADUC7024BCPZ62 IC MCU FLSH 62K ANLG I/O 64LFCSP
ADUC7032BSTZ-88 IC MCU 96K FLASH DUAL 48LQFP
ADUC7032BSTZ-8V-RL IC BATTERY SENSOR PREC 48-LQFP
相关代理商/技术参数
参数描述
ADSP-TS203SABP-05X 制造商:Analog Devices 功能描述:
ADSP-TS203SABPZ050 功能描述:IC PROCESSOR 500MHZ 576BGA RoHS:是 类别:集成电路 (IC) >> 嵌入式 - DSP(数字式信号处理器) 系列:TigerSHARC® 标准包装:2 系列:StarCore 类型:SC140 内核 接口:DSI,以太网,RS-232 时钟速率:400MHz 非易失内存:外部 芯片上RAM:1.436MB 电压 - 输入/输出:3.30V 电压 - 核心:1.20V 工作温度:-40°C ~ 105°C 安装类型:表面贴装 封装/外壳:431-BFBGA,FCBGA 供应商设备封装:431-FCPBGA(20x20) 包装:托盘
ADSP-TS203SBBPZ050 制造商:Analog Devices 功能描述:DSP - Bulk
ADSQ-1410 制造商:MURATA-PS 制造商全称:Murata Power Solutions Inc. 功能描述:Quad 14-Bit, 10 MSPS Sampling A/D Converter
ADSQ-1410-C 制造商:MURATA-PS 制造商全称:Murata Power Solutions Inc. 功能描述:Quad 14-Bit, 10 MSPS Sampling A/D Converter