参数资料
型号: ADSP-TS203SABP-050
厂商: Analog Devices Inc
文件页数: 9/48页
文件大小: 0K
描述: IC DSP FLOAT/FIXED 500MHZ 576BGA
标准包装: 1
系列: TigerSHARC®
类型: 定点/浮点
接口: 主机接口,连接端口,多处理器
时钟速率: 500MHz
非易失内存: 外部
芯片上RAM: 512kB
电压 - 输入/输出: 2.50V
电压 - 核心: 1.05V
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 576-BBGA 裸露焊盘
供应商设备封装: 576-BGA-ED(25x25)
包装: 托盘
其它名称: ADSP-TS203SABP050
ADSP-TS203SABP050-ND
Rev. D
|
Page 17 of 48
|
May 2012
Table 12. Pin Definitions—Impedance Control, Drive Strength Control, and Regulator Enable
Signal
Type
Term
Description
CONTROLIMP0
CONTROLIMP1
I (pd)
I (pu)
na
Impedance Control. As shown in Table 13, the CONTROLIMP1–0 pins select between
normal driver mode and A/D driver mode. When using normal mode (recommended),
the output drive strength is set relative to maximum drive strength according to
Table 14. When using A/D mode, the resistance control operates in the analog mode,
where drive strength is continuously controlled to match a specific line impedance as
shown in Table 14.
DS2, 0
DS1
I (pu)
I (pd)
na
Digital Drive Strength Selection. Selected as shown in Table 14. For drive strength
calculation, see Output Drive Currents on Page 34. The drive strength for some pins is
preset, not controlled by the DS2–0 pins. The pins that are always at drive strength 7
(100%) include: CPA, DPA, TDO, EMU, and RST_OUT. The drive strength for the ACK pin
is always ×2 drive strength 7 (100%).
ENEDREG
I (pu)
VSS
Connect the ENEDREG pin to VSS. Connect the VDD_DRAM pins to a properly decoupled
DRAM power supply.
I = input; A = asynchronous; O = output; OD = open-drain output; T = three-state; P = power supply; G = ground; pd = internal pull-down
5kΩ; pu = internal pull-up 5 kΩ; pd_0 = internal pull-down 5 kΩ on processor ID = 0; pu_0 = internal pull-up 5 kΩ on processor ID = 0;
pu_od_0 = internal pull-up 500 Ω on processor ID = 0; pd_m = internal pull-down 5 kΩ on processor bus master; pu_m = internal pull-up
5 kΩ on processor bus master; pu_ad = internal pull-up 40 kΩ. For more pull-down and pull-up information, see Electrical Characteristics
Term (termination of unused pins) column symbols: epd = external pull-down approximately 5 kΩ to VSS; epu = external pull-up
approximately 5 kΩ to VDD_IO, nc = not connected; na = not applicable (always used); VDD_IO = connect directly to VDD_IO; VSS = connect
directly to VSS
Table 13. Impedance Control Selection
CONTROLIMP1-0
Driver Mode
00 (recommended)
Normal
01
Reserved
10 (default)
A/D Mode
11
Reserved
Table 14. Drive Strength/Output Impedance Selection
DS2–0
Pins
Drive
Strength1
Output
Impedance 2
000
Strength 0 (11.1%)
26 Ω
001
Strength 1 (23.8%)
32 Ω
010
Strength 2 (36.5%)
40 Ω
011
Strength 3 (49.2%)
50 Ω
100
Strength 4 (61.9%)
62 Ω
101 (default)
Strength 5 (74.6%)
70 Ω
110
Strength 6 (87.3%)
96 Ω
111
Strength 7 (100%)
120 Ω
1 CONTROLIMP1 = 0, A/D mode disabled.
2 CONTROLIMP1 = 1, A/D mode enabled.
相关PDF资料
PDF描述
ADUC7021BCPZ62-RL7 IC MCU 12BIT 1MSPS UART 40-LFCSP
ADUC7023BCPZ62I-R7 IC MCU 12BIT 62KB FLASH 32LFCSP
ADUC7024BCPZ62 IC MCU FLSH 62K ANLG I/O 64LFCSP
ADUC7032BSTZ-88 IC MCU 96K FLASH DUAL 48LQFP
ADUC7032BSTZ-8V-RL IC BATTERY SENSOR PREC 48-LQFP
相关代理商/技术参数
参数描述
ADSP-TS203SABP-05X 制造商:Analog Devices 功能描述:
ADSP-TS203SABPZ050 功能描述:IC PROCESSOR 500MHZ 576BGA RoHS:是 类别:集成电路 (IC) >> 嵌入式 - DSP(数字式信号处理器) 系列:TigerSHARC® 标准包装:2 系列:StarCore 类型:SC140 内核 接口:DSI,以太网,RS-232 时钟速率:400MHz 非易失内存:外部 芯片上RAM:1.436MB 电压 - 输入/输出:3.30V 电压 - 核心:1.20V 工作温度:-40°C ~ 105°C 安装类型:表面贴装 封装/外壳:431-BFBGA,FCBGA 供应商设备封装:431-FCPBGA(20x20) 包装:托盘
ADSP-TS203SBBPZ050 制造商:Analog Devices 功能描述:DSP - Bulk
ADSQ-1410 制造商:MURATA-PS 制造商全称:Murata Power Solutions Inc. 功能描述:Quad 14-Bit, 10 MSPS Sampling A/D Converter
ADSQ-1410-C 制造商:MURATA-PS 制造商全称:Murata Power Solutions Inc. 功能描述:Quad 14-Bit, 10 MSPS Sampling A/D Converter