- 您现在的位置：买卖IC网 > PDF目录1900 > ADSP-TS203SABP-050 (Analog Devices Inc)IC DSP FLOAT/FIXED 500MHZ 576BGA PDF资料下载
参数资料
| 型号： | ADSP-TS203SABP-050 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 6/48页 |
| 文件大小： | 0K |
| 描述： | IC DSP FLOAT/FIXED 500MHZ 576BGA |
| 标准包装： | 1 |
| 系列： | TigerSHARC® |
| 类型： | 定点/浮点 |
| 接口： | 主机接口，连接端口，多处理器 |
| 时钟速率： | 500MHz |
| 非易失内存： | 外部 |
| 芯片上RAM： | 512kB |
| 电压 - 输入/输出： | 2.50V |
| 电压 - 核心： | 1.05V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 576-BBGA 裸露焊盘 |
| 供应商设备封装： | 576-BGA-ED（25x25） |
| 包装： | 托盘 |
| 其它名称： | ADSP-TS203SABP050 ADSP-TS203SABP050-ND |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
Rev. D
|
Page 14 of 48
|
May 2012
Table 7. Pin Definitions—External Port DMA/Flyby
Signal
Type
Term
Description
DMAR3–0
I/A
epu
DMA Request Pins. Enable external I/O devices to request DMA services from the
processor. In response to DMARx, the processor performs DMA transfers according
to the DMA channel’s initialization. The processor ignores DMA requests from unini-
tialized channels.
IOWR
O/T
(pu_0)
nc
I/O Write. When a processor DMA channel initiates a flyby mode read transaction,
the processor asserts the IOWR signal during the data cycles. This assertion makes
the I/O device sample the data instead of the TigerSHARC.
IORD
O/T
(pu_0)
nc
I/O Read. When a processor DMA channel initiates a flyby mode write transaction,
the processor asserts the IORD signal during the data cycle. This assertion with the
IOEN makes the I/O device drive the data instead of the TigerSHARC.
IOEN
O/T
(pu_0)
nc
I/O Device Output Enable. Enables the output buffers of an external I/O device for
fly-by transactions between the device and external memory. Active on flyby
transactions.
I = input; A = asynchronous; O = output; OD = open-drain output; T = three-state; P = power supply; G = ground; pd = internal pull-down
5kΩ; pu = internal pull-up 5 kΩ; pd_0 = internal pull-down 5 kΩ on processor ID = 0; pu_0 = internal pull-up 5 kΩ on processor ID = 0;
pu_od_0 = internal pull-up 500 Ω on processor ID = 0; pd_m = internal pull-down 5 kΩ on processor bus master; pu_m = internal pull-up
5 kΩ on processor bus master; pu_ad = internal pull-up 40 kΩ. For more pull-down and pull-up information, see Electrical Characteristics
Term (termination of unused pins) column symbols: epd = external pull-down approximately 5 kΩ to VSS; epu = external pull-up
approximately 5 kΩ to VDD_IO, nc = not connected; na = not applicable (always used); VDD_IO = connect directly to VDD_IO; VSS = connect
directly to VSS
Table 8. Pin Definitions—External Port SDRAM Controller
Signal
Type
Term
Description
MSSD3–0
I/O/T
(pu_0)
nc
Memory Select SDRAM. MSSD0, MSSD1, MSSD2, or MSSD3 is asserted whenever the
processor accesses SDRAM memory space. MSSD3–0 are decoded memory address
pins that are asserted whenever the processor issues an SDRAM command cycle
(access to ADDR31:30 = 0b01—except reserved spaces shown in Figure 2 on
Page 6). In a multiprocessor system, the master processor drives MSSD3–0.
RAS
I/O/T
(pu_0)
nc
Row Address Select. When sampled low, RAS indicates that a row address is valid in
a read or write of SDRAM. In other SDRAM accesses, it defines the type of operation
to execute according to SDRAM specification.
CAS
I/O/T
(pu_0)
nc
Column Address Select. When sampled low, CAS indicates that a column address is
valid in a read or write of SDRAM. In other SDRAM accesses, it defines the type of
operation to execute according to the SDRAM specification.
LDQM
O/T
(pu_0)
nc
Low Word SDRAM Data Mask. When sampled high, three-states the SDRAM DQ
buffers. LDQM is valid on SDRAM transactions when CAS is asserted, and inactive
on read transactions.
I = input; A = asynchronous; O = output; OD = open-drain output; T = three-state; P = power supply; G = ground; pd = internal pull-down
5kΩ; pu = internal pull-up 5 kΩ; pd_0 = internal pull-down 5 kΩ on processor ID = 0; pu_0 = internal pull-up 5 kΩ on processor ID = 0;
pu_od_0 = internal pull-up 500 Ω on processor ID = 0; pd_m = internal pull-down 5 kΩ on processor bus master; pu_m = internal pull-up
5 kΩ on processor bus master; pu_ad = internal pull-up 40 kΩ. For more pull-down and pull-up information, see Electrical Characteristics
Term (termination of unused pins) column symbols: epd = external pull-down approximately 5 kΩ to VSS; epu = external pull-up
approximately 5 kΩ to VDD_IO, nc = not connected; na = not applicable (always used); VDD_IO = connect directly to VDD_IO; VSS = connect
directly to VSS
相关PDF资料 |
PDF描述 |
|---|---|
| ADUC7021BCPZ62-RL7 | IC MCU 12BIT 1MSPS UART 40-LFCSP |
| ADUC7023BCPZ62I-R7 | IC MCU 12BIT 62KB FLASH 32LFCSP |
| ADUC7024BCPZ62 | IC MCU FLSH 62K ANLG I/O 64LFCSP |
| ADUC7032BSTZ-88 | IC MCU 96K FLASH DUAL 48LQFP |
| ADUC7032BSTZ-8V-RL | IC BATTERY SENSOR PREC 48-LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADSP-TS203SABP-05X | 制造商:Analog Devices 功能描述: |
| ADSP-TS203SABPZ050 | 功能描述:IC PROCESSOR 500MHZ 576BGA RoHS:是 类别:集成电路 (IC) >> 嵌入式 - DSP（数字式信号处理器） 系列:TigerSHARC® 标准包装:2 系列:StarCore 类型:SC140 内核 接口:DSI，以太网，RS-232 时钟速率:400MHz 非易失内存:外部 芯片上RAM:1.436MB 电压 - 输入/输出:3.30V 电压 - 核心:1.20V 工作温度:-40°C ~ 105°C 安装类型:表面贴装 封装/外壳:431-BFBGA，FCBGA 供应商设备封装:431-FCPBGA（20x20） 包装:托盘 |
| ADSP-TS203SBBPZ050 | 制造商:Analog Devices 功能描述:DSP - Bulk |
| ADSQ-1410 | 制造商:MURATA-PS 制造商全称:Murata Power Solutions Inc. 功能描述:Quad 14-Bit, 10 MSPS Sampling A/D Converter |
| ADSQ-1410-C | 制造商:MURATA-PS 制造商全称:Murata Power Solutions Inc. 功能描述:Quad 14-Bit, 10 MSPS Sampling A/D Converter |
发布紧急采购，3分钟左右您将得到回复。