收藏本站
参数资料
型号： AGLE3000V2-FG896I
厂商： Microsemi SoC
文件页数： 33/166页
文件大小： 0K
描述： IC FPGA 1KB FLASH 3M 896-FBGA
标准包装： 27
系列： IGLOOe
逻辑元件/单元数： 75264
RAM 位总计： 516096
输入/输出数： 620
门数： 3000000
电源电压： 1.14 V ~ 1.575 V
安装类型： 表面贴装
工作温度： -40°C ~ 85°C
封装/外壳： 896-BGA
供应商设备封装： 896-FBGA（31x31）
Pin Descriptions and Packaging
3-4
Revision 13
Table 3-1 shows the Flash*Freeze pin location on the available packages. The Flash*Freeze pin location
is independent of device (except for a PQ208 package), allowing migration to larger or smaller IGLOO
devices while maintaining the same pin location on the board. Refer to the "Flash*Freeze Technology
and Low Power Modes" chapter of the IGLOOe FPGA Fabric User’s Guide for more information on I/O
states during Flash*Freeze mode.
JTAG Pins
Low power flash devices have a separate bank for the dedicated JTAG pins. The JTAG pins can be run
at any voltage from 1.5 V to 3.3 V (nominal). VCC must also be powered for the JTAG state machine to
operate, even if the device is in bypass mode; VJTAG alone is insufficient. Both VJTAG and VCC to the
part must be supplied to allow JTAG signals to transition the device. Isolating the JTAG power supply in a
separate I/O bank gives greater flexibility in supply selection and simplifies power supply and PCB
design. If the JTAG interface is neither used nor planned for use, the VJTAG pin together with the TRST
pin could be tied to GND.
TCK
Test Clock
Test clock input for JTAG boundary scan, ISP, and UJTAG. The TCK pin does not have an internal pull-
up/-down resistor. If JTAG is not used, Microsemi recommends tying off TCK to GND through a resistor
placed close to the FPGA pin. This prevents JTAG operation in case TMS enters an undesired state.
Note that to operate at all VJTAG voltages, 500
to 1 k will satisfy the requirements. Refer to Table 3-2
for more information.
Table 3-1 Flash*Freeze Pin Locations for IGLOOe Devices
Package
Flash*Freeze Pin
FG256
T3
FG484
W6
FG896
AH4
Table 3-2 Recommended Tie-Off Values for the TCK and TRST Pins
VJTAG
Tie-Off Resistance 1,2
VJTAG at 3.3 V
200
to 1 k
VJTAG at 2.5 V
200
to 1 k
VJTAG at 1.8 V
500
to 1 k
VJTAG at 1.5 V
500
to 1 k
Notes:
1. The TCK pin can be pulled-up or pulled-down.
2. The TRST pin is pulled-down.
3. Equivalent parallel resistance if more than one device is on the JTAG chain
相关PDF资料
PDF描述
24LC024T/SN IC EEPROM 2KBIT 400KHZ 8SOIC
AGLE3000V2-FGG896I IC FPGA 1KB FLASH 3M 896-FBGA
M1AGLE3000V2-FGG896I IC FPGA 1KB FLASH 3M 896-FBGA
24LC024T-I/SN IC EEPROM 2KBIT 400KHZ 8SOIC
APA1000-PQG208I IC FPGA PROASIC+ 1M 208-PQFP
相关代理商/技术参数
参数描述
AGLE3000V2-FG896PP 制造商:ACTEL 制造商全称:Actel Corporation 功能描述:IGLOOe Low-Power Flash FPGAs with Flash Freeze Technology
AGLE3000V2-FGG484 功能描述:IC FPGA 1KB FLASH 3M 484-FBGA RoHS:是 类别:集成电路 (IC) >> 嵌入式 - FPGA（现场可编程门阵列） 系列:IGLOOe 标准包装:1 系列:ProASICPLUS LAB/CLB数:- 逻辑元件/单元数:- RAM 位总计:129024 输入/输出数:248 门数:600000 电源电压:2.3 V ~ 2.7 V 安装类型:表面贴装 工作温度:- 封装/外壳:352-BFCQFP，带拉杆 供应商设备封装:352-CQFP（75x75）
AGLE3000V2-FGG484I 功能描述:IC FPGA 1KB FLASH 3M 484-FBGA RoHS:是 类别:集成电路 (IC) >> 嵌入式 - FPGA（现场可编程门阵列） 系列:IGLOOe 标准包装:1 系列:ProASICPLUS LAB/CLB数:- 逻辑元件/单元数:- RAM 位总计:129024 输入/输出数:248 门数:600000 电源电压:2.3 V ~ 2.7 V 安装类型:表面贴装 工作温度:- 封装/外壳:352-BFCQFP，带拉杆 供应商设备封装:352-CQFP（75x75）
AGLE3000V2-FGG896 功能描述:IC FPGA 1KB FLASH 3M 896-FBGA RoHS:是 类别:集成电路 (IC) >> 嵌入式 - FPGA（现场可编程门阵列） 系列:IGLOOe 标准包装:1 系列:ProASICPLUS LAB/CLB数:- 逻辑元件/单元数:- RAM 位总计:129024 输入/输出数:248 门数:600000 电源电压:2.3 V ~ 2.7 V 安装类型:表面贴装 工作温度:- 封装/外壳:352-BFCQFP，带拉杆 供应商设备封装:352-CQFP（75x75）
AGLE3000V2-FGG896ES 制造商:ACTEL 制造商全称:Actel Corporation 功能描述:IGLOOe Low-Power Flash FPGAs with Flash Freeze Technology
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*