- 您现在的位置：买卖IC网 > PDF目录11590 > CP2201-GM (Silicon Laboratories Inc)IC ETH CTRLR SNGL-CHIP 28QFN PDF资料下载
参数资料
| 型号： | CP2201-GM |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 52/108页 |
| 文件大小： | 0K |
| 描述： | IC ETH CTRLR SNGL-CHIP 28QFN |
| 标准包装： | 73 |
| 控制器类型： | 以太网控制器，MAC/10Base-T |
| 接口： | 并行/串行 |
| 电源电压： | 3.1 V ~ 3.6 V |
| 电流 - 电源： | 75mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-VFQFN 裸露焊盘 |
| 供应商设备封装： | 28-QFN（5x5） |
| 包装： | 管件 |
| 产品目录页面： | 627 (CN2011-ZH PDF) |
| 配用： | 336-1326-ND - KIT REF DESIGN PWR OVER ETHERNET 336-1316-ND - KIT EVAL FOR CP2201 ETH CTRLR |
| 其它名称： | 336-1313 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页当前第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页
CP2200/1
48
Rev. 1.0
11.2. Transmitting a Packet
Once reset initialization is complete (See ), the CP2200/1 is ready to transmit Ethernet packets. The following
procedure can be used to transmit a packet:
Step 1: Wait for the previous packet to complete (TXBUSY == 0x00). The worst case time to transmit a
packet is 500 ms in half-duplex mode with exponential backoff.
Step 2: Set the TXSTARTH:TXSTARTL transmit buffer pointer to 0x0000.
Step 3: If the last packet was aborted ((TXSTA3 & 0xF8) != 0x00), then this packet must be loaded into the
transmit buffer using the Random Memory Access Method:
a. Set RAMADDRH:RAMADDRL to 0x0000.
b. Write the first data byte to RAMTXDATA.
c. Increment RAMADDRH:RAMADDRL.
d. Write another data byte to RAMTXDATA.
e. Repeat steps c and d until the entire packet is loaded.
f. Pad small packets to at least 64 bytes.
g. Set TXENDH:TXENDL to the address of the last byte added. This value must be greater than or
equal to 0x0040.
Step 4: If the last packet was successfully transmitted ((TXSTA2 & 0x80) == 0x80), then this packet may be
loaded into the transmit buffer using the AutoWrite Interface:
a. Write all data bytes to the TXAUTOWR register, one byte at time.
b. If the MAC is in half-duplex mode, pad small packets to at least 64 bytes.
Step 5: Set the TXSTARTH:TXSTARTL transmit buffer pointer back to 0x0000.
Step 6: Write a ‘1’ to the TXGO bit (TXCN.0) to begin transmission.
Note: Step 4 may be skipped if Step 3 is always performed.
11.3. Overriding Transmit Configuration Options
The global transmit configuration options are set in the MAC registers. The transmit interface allows the host
processor to customize packet transmission on a per-packet basis by overriding the global MAC settings. The
following options can be overridden by the transmit interface:
Short Frame Padding—When enabled, ensures that no frame smaller than 64 bytes is transmitted. The frame
size does not include the 8 byte preamble; however, the 4-byte CRC field is included.
CRC Generation—When enabled, a 32-bit CRC will be calculated and appended to the Ethernet frame.
Pause packet transmission (Full Duplex Mode)—When enabled, an Ethernet PAUSE packet with a pause value
of TXPAUSEH:TXPAUSEL is transmitted. The pause value is in units of 512 bit times (51.2 s).
Application of Back Pressure (Half Duplex Mode).
Switching between Half/Full Duplex Modes. Note: This setting does not affect the physical layer.
11.4. Transmit Buffer and AutoWrite Interface
The transmit buffer provides the AutoWrite interface to efficiently load the buffer with an entire packet. The interface
consists of three registers: TXSTART, TXEND, and TXAUTOWR. The TXSTART register points to the address of
the next available byte and can be reset to the first byte of the buffer. TXEND points to the last byte added to the
buffer. TXAUTOWR is the data register. Each write to TXAUTOWR sets TXEND to the address of the byte written
and increments TXSTART. After the packet is loaded into the buffer, TXSTART is reset to 0x0000 to mark the
starting point of the packet. TXEND will continue to point to the last byte in the packet.
Note: The AutoWrite Interface cannot be used following an aborted packet. This only applies if the device is in half-duplex
mode.
相关PDF资料 |
PDF描述 |
|---|---|
| PIC12C509A-04I/MF | IC MCU OTP 1KX12 8DFN |
| VNC2-64L1B-REEL | IC USB HOST/DEVICE CTRL 64-LQFP |
| PIC12CE518T-04/SN | IC MCU OTP 512X12 W/EE 8SOIC |
| GRM219R71E563KA01D | CAP CER 0.056UF 25V 10% X7R 0805 |
| PIC16LF723T-I/SO | IC PIC MCU FLASH 7KB 28-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CP2201-GMR | 功能描述:以太网 IC Ethernet Controller RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| CP-220-K | 制造商:PREMO 制造商全称:PREMO CORPORATION S.L 功能描述:Coils and Chokes for general use |
| CP221 | 制造商:CENTRAL 制造商全称:Central Semiconductor Corp 功能描述:Small Signal Transistor |
| CP-221 1 1/2"BL 100' | 功能描述:HEATSHRNK CP221 1-1/2" X 100'BLK 制造商:3m 系列:CP-221 零件状态:过期 类型:套管，弹性 收缩率:2 至 1 长度:100'（30.48m） 内径（出厂）:1.500"（38.1mm） 内径 - 恢复后:0.752"（19.1mm） 恢复后的壁厚:0.040"（1.02mm） 材料:聚烯烃（PO） 特性:自熄灭 颜色:黑 工作温度:-55°C ~ 135°C 收缩温度:121°C 标准包装:1 |
| CP-221 1 1/2"BL 100' | 制造商:3M Electronic Products Division 功能描述:HEATSHRNK CP221 1-1/2" X 100'BLK 制造商:3M Electronic Products Division 功能描述:HEATSHRNK CP221 1-1/2" X 25' BLK |
发布紧急采购，3分钟左右您将得到回复。