- 您现在的位置：买卖IC网 > PDF目录11590 > CP2201-GM (Silicon Laboratories Inc)IC ETH CTRLR SNGL-CHIP 28QFN PDF资料下载
参数资料
| 型号： | CP2201-GM |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 63/108页 |
| 文件大小： | 0K |
| 描述： | IC ETH CTRLR SNGL-CHIP 28QFN |
| 标准包装： | 73 |
| 控制器类型： | 以太网控制器，MAC/10Base-T |
| 接口： | 并行/串行 |
| 电源电压： | 3.1 V ~ 3.6 V |
| 电流 - 电源： | 75mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-VFQFN 裸露焊盘 |
| 供应商设备封装： | 28-QFN（5x5） |
| 包装： | 管件 |
| 产品目录页面： | 627 (CN2011-ZH PDF) |
| 配用： | 336-1326-ND - KIT REF DESIGN PWR OVER ETHERNET 336-1316-ND - KIT EVAL FOR CP2201 ETH CTRLR |
| 其它名称： | 336-1313 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页当前第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页
CP2200/1
58
Rev. 1.0
12. Receive Interface
12.1. Overview
The CP2200/1 has a 4k circular receive FIFO buffer and an 8 entry translation look-aside buffer (TLB) capable of
storing up to 8 packets at a time. Each TLB entry holds the starting address, length, and other information about a
single received packet. Once a packet is received, the host microcontroller is notified using the interrupt request
pin. The host microcontroller may then copy the contents of the packet to its local memory through the host
interface or skip the packet by writing ‘1’ to RXSKIP (RXCN.1). Skipped packets remain in memory but will be
overwritten as new packets arrive.
The receive interface has an advanced receive filter and hash table to prevent unwanted packets from reaching the
receive buffer. For all packet types not supported by the receive filter, the CP2200/1 allows the host microcontroller
complete random access to the receive buffer. The host microcontroller can check specific bytes in the packet to
determine whether or not to copy the packet.
.
Figure 17. Receive Interface Block Diagram
12.2. Reading a Packet Using the Autoread Interface
Once reset initialization is complete (Section 6.2 on page 18) and the receive buffer, filter, and hash table (Section
12.4) are initialized, the CP2200/1 is ready to receive Ethernet packets. After receiving notification of a new packet,
the following procedure can be used to read the packet:
Step 1: Read RXVALID (CPINFOH.7) and RXOK (CPINFOL.7) to check if the current packet was received
correctly. The host processor may optionally use the packet starting address CPADDR to read
specific bytes in the packet and determine whether to copy or skip the current packet. The random
access method described in Section 7.1 on page 23 can be used to access the buffer.
Step 2: If RXVALID or RXOK is 0, or to skip the packet, write a ‘1’ to RXSKIP (RXCN.1).
If RXVALID and RXOK are 1, read the length of the current packet from CPLENH:CPLENL.
Step 3: Read the entire packet, one byte at a time, by reading RXAUTORD.
Step 4: If the entire packet was read, write a ‘1’ to RXCLRV (RXCN.2).
If there are any unread bytes remaining in the current buffer, write a ‘1’ to RXSKIP (RXCN.1).
12.3. Timing and Buffer Overflow Considerations
For 10 Base-T Ethernet, a minimum-sized packet of 64 bytes is received in 51.2 us. The maximum number of
packets that can be held by the receive buffer is eight. To ensure that pointer corruption does not occur, software
should disable packet reception (RXINH = 1) after the seventh packet has arrived in the receive buffer. If the ability
to service the packet received interrupt is longer than 51.2us, then software should use the random access method
to retrieve data from the receive buffer. The random access method described in Section 7.1 on page 23.
4 KB
Receive
Buffer
with
8-entry TLB
Programmable
Receive Filter and
Hash Table
Host Interface Registers
Autoread Interface:
Autoread Data Register
Packet Skip Bit
Current Packet:
Packet Address
Packet Length
Packet Information
相关PDF资料 |
PDF描述 |
|---|---|
| PIC12C509A-04I/MF | IC MCU OTP 1KX12 8DFN |
| VNC2-64L1B-REEL | IC USB HOST/DEVICE CTRL 64-LQFP |
| PIC12CE518T-04/SN | IC MCU OTP 512X12 W/EE 8SOIC |
| GRM219R71E563KA01D | CAP CER 0.056UF 25V 10% X7R 0805 |
| PIC16LF723T-I/SO | IC PIC MCU FLASH 7KB 28-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CP2201-GMR | 功能描述:以太网 IC Ethernet Controller RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| CP-220-K | 制造商:PREMO 制造商全称:PREMO CORPORATION S.L 功能描述:Coils and Chokes for general use |
| CP221 | 制造商:CENTRAL 制造商全称:Central Semiconductor Corp 功能描述:Small Signal Transistor |
| CP-221 1 1/2"BL 100' | 功能描述:HEATSHRNK CP221 1-1/2" X 100'BLK 制造商:3m 系列:CP-221 零件状态:过期 类型:套管，弹性 收缩率:2 至 1 长度:100'（30.48m） 内径（出厂）:1.500"（38.1mm） 内径 - 恢复后:0.752"（19.1mm） 恢复后的壁厚:0.040"（1.02mm） 材料:聚烯烃（PO） 特性:自熄灭 颜色:黑 工作温度:-55°C ~ 135°C 收缩温度:121°C 标准包装:1 |
| CP-221 1 1/2"BL 100' | 制造商:3M Electronic Products Division 功能描述:HEATSHRNK CP221 1-1/2" X 100'BLK 制造商:3M Electronic Products Division 功能描述:HEATSHRNK CP221 1-1/2" X 25' BLK |
发布紧急采购，3分钟左右您将得到回复。