CP2201-GM (Silicon) PDF资料下载 Datasheet(85/108 页)

您现在的位置：买卖IC网 > PDF目录11590 > CP2201-GM (Silicon Laboratories Inc)IC ETH CTRLR SNGL-CHIP 28QFN PDF资料下载

参数资料

型号：	CP2201-GM
厂商：	Silicon Laboratories Inc
文件页数：	85/108页
文件大小：	0K
描述：	IC ETH CTRLR SNGL-CHIP 28QFN
标准包装：	73
控制器类型：	以太网控制器，MAC/10Base-T
接口：	并行/串行
电源电压：	3.1 V ~ 3.6 V
电流 - 电源：	75mA
工作温度：	-40°C ~ 85°C
安装类型：	表面贴装
封装/外壳：	28-VFQFN 裸露焊盘
供应商设备封装：	28-QFN（5x5）
包装：	管件
产品目录页面：	627 (CN2011-ZH PDF)
配用：	336-1326-ND - KIT REF DESIGN PWR OVER ETHERNET 336-1316-ND - KIT EVAL FOR CP2201 ETH CTRLR
其它名称：	336-1313

CP2200/1

Rev. 1.0

14. Media Access Controller (MAC)

The CP2200/1 has an IEEE 802.3 compliant Ethernet Media Access Controller (MAC). The MAC can be

configured to automatically pad short frames (full duplex mode only), append CRC, and perform frame length

checking. A loopback mode separate from PHY loopback is also provided for system debugging. The MAC is

configured through nine indirect 16-bit registers summarized in Table 20.

14.1. Initializing the MAC

MAC initialization occurs after the physical layer initialization and typically occurs once after each reset or Auto-

Negotiation Complete interrupt. Most MAC indirect registers can be left at their reset values. See “6.2. Reset

Initialization” on page 18 for the complete reset initialization procedure. The following are the steps required to

initialize the MAC:

Step 1: Determine if the physical layer is set to full-duplex or half-duplex. The MAC must be set to the same

duplex mode as the physical layer before sending or receiving any packets.

Step 2: Write 0x40B3 (full-duplex) or 0x4012 (half-duplex) to MACCF. The appropriate bits in this register

may also be set or cleared to change padding options or MAC behavior.

Step 3: Write 0x0015 (full-duplex) or 0x0012 (half-duplex) to IPGT.

Step 4: Write 0x0C12 to IPGR.

Step 5: Write 0x05EE to MAXLEN.

Step 6: Program the 48-bit Ethernet MAC Address by writing to MACAD0:MACAD1:MACAD2.

Step 7: Write 0x0001 to MACCN to enable reception. If loopback mode or flow control is desired, set the

appropriate bits to enable these functions.

14.2. Accessing the Indirect MAC Registers

The indirect MAC registers are accessed through four direct mapped registers: MACADDR, MACDATAH,

MACDATAL, and MACRW. The MAC registers can be accessed using the following procedure:

Step 1: Write the address of the indirect register to MACADDR.

Step 2: If writing a value to the indirect register, write a 16-bit value to MACDATAH:MACDATAL.

Step 3: Write any value to MACRW to transfer the contents of MACDATAH:MACDATAL to the indirect

Step 4: Perform a read on MACRW to transfer the contents of the indirect register to

MACDATAH:MACDATAL. The MACDATAH and MACDATAL registers may now be directly read to

determine the contents of the indirect register.

相关代理商/技术参数	参数描述
CP2201-GMR	功能描述:以太网 IC Ethernet Controller RoHS:否制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray
CP-220-K	制造商:PREMO 制造商全称:PREMO CORPORATION S.L 功能描述:Coils and Chokes for general use
CP221	制造商:CENTRAL 制造商全称:Central Semiconductor Corp 功能描述:Small Signal Transistor
CP-221 1 1/2"BL 100'	功能描述:HEATSHRNK CP221 1-1/2" X 100'BLK 制造商:3m 系列:CP-221 零件状态:过期类型:套管，弹性收缩率:2 至 1 长度:100'（30.48m）内径（出厂）:1.500"（38.1mm）内径 - 恢复后:0.752"（19.1mm）恢复后的壁厚:0.040"（1.02mm）材料:聚烯烃（PO）特性:自熄灭颜色:黑工作温度:-55°C ~ 135°C 收缩温度:121°C 标准包装:1
CP-221 1 1/2"BL 100'	制造商:3M Electronic Products Division 功能描述:HEATSHRNK CP221 1-1/2" X 100'BLK 制造商:3M Electronic Products Division 功能描述:HEATSHRNK CP221 1-1/2" X 25' BLK

发布紧急采购，3分钟左右您将得到回复。

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购