参数资料
型号: DS2154LNA2+
厂商: Maxim Integrated Products
文件页数: 118/124页
文件大小: 0K
描述: IC TXRX E1 5V 100-LQFP
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 90
类型: 收发器
驱动器/接收器数: 1/1
规程: E1
电源电压: 4.75 V ~ 5.25 V
安装类型: 表面贴装
封装/外壳: 100-LQFP
供应商设备封装: 100-LQFP(14x14)
包装: 托盘
DS21354/DS21554 3.3V/5V E1 Single-Chip Transceivers
93 of 124
Select-IR-Scan
All test registers retain their previous state. The instruction register will remain unchanged during this
state. With JTMS LOW, a rising edge on JTCLK moves the controller into the Capture-IR state and will
initiate a scan sequence for the instruction register. JTMS HIGH during a rising edge on JTCLK puts the
controller back into the Test-Logic-Reset state.
Capture-IR
The Capture-IR state is used to load the shift register in the instruction register with a fixed value. This
value is loaded on the rising edge of JTCLK. If JTMS is HIGH on the rising edge of JTCLK, the
controller will enter the Exit1-IR state. If JTMS is LOW on the rising edge of JTCLK, the controller will
enter the Shift-IR state.
Shift-IR
In this state, the shift register in the instruction register is connected between JTDI and JTDO and shifts
data one stage for every rising edge of JTCLK towards the serial output. The parallel register, as well as
all test registers, remain at their previous states. A rising edge on JTCLK with JTMS HIGH will move the
controller to the Exit1-IR state. A rising edge on JTCLK with JTMS LOW will keep the controller in the
Shift-IR state while moving data one stage thorough the instruction shift register.
Exit1-IR
A rising edge on JTCLK with JTMS LOW will put the controller in the Pause-IR state. If JTMS is HIGH
on the rising edge of JTCLK, the controller will enter the Update-IR state and terminate the scanning
process.
Pause-IR
Shifting of the instruction shift register is halted temporarily. With JTMS HIGH, a rising edge on JTCLK
will put the controller in the Exit2-IR state. The controller will remain in the Pause-IR state if JTMS is
LOW during a rising edge on JTCLK.
Exit2-IR
A rising edge on JTCLK with JTMS LOW will put the controller in the Update-IR state. The controller
will loop back to Shift-IR if JTMS is HIGH during a rising edge of JTCLK in this state.
Update-IR
The instruction code shifted into the instruction shift register is latched into the parallel output on the
falling edge of JTCLK as the controller enters this state. Once latched, this instruction becomes the
current instruction. A rising edge on JTCLK with JTMS LOW, will put the controller in the Run-Test-
Idle state. With JTMS HIGH, the controller will enter the Select-DR-Scan state.
相关PDF资料
PDF描述
DS2154L IC TXRX E1 1CHIP 5V ENH 100-LQFP
DS2155LN IC TXRX T1/E1/J1 1-CHIP 100-LQFP
DS2156LN+ IC TXRX T1/E1/J1 1-CHIP 100-LQFP
DS2172T/T&R IC TESTER BIT ERROR RATE 32-TQFP
DS2174QN+ IC BERT ENHANCED 44-PLCC
相关代理商/技术参数
参数描述
DS2154LNA2+ 功能描述:网络控制器与处理器 IC Enhanced E1 Transceiver RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
DS2154LND2 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
DS2154LND2+ 制造商:Maxim Integrated Products 功能描述:ENHANCED E1 SCT LQFP REVD2 IND LF - Rail/Tube
DS2155 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:T1/E1/J1 Single-Chip Transceiver TDM/UTOPIA II Interface
DS2155_06 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:T1/E1/J1 Single-Chip Transceiver