- 您现在的位置：买卖IC网 > PDF目录97869 > DS3131 (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY TELECOM CIRCUIT, PBGA256 PDF资料下载
参数资料
| 型号： | DS3131 |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | Telecom IC:Other |
| 英文描述： | SPECIALTY TELECOM CIRCUIT, PBGA256 |
| 封装： | 27 X 27 MM, PLASTIC, BGA-256 |
| 文件页数： | 137/174页 |
| 文件大小： | 1261K |
| 代理商： | DS3131 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页当前第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页第160页第161页第162页第163页第164页第165页第166页第167页第168页第169页第170页第171页第172页第173页第174页
DS3131
65 of 174
8. FIFO
8.1 General Description and Example
The BoSS contains one 8kB FIFO for the receive path and another 8kB FIFO for the transmit path. Both
of these FIFOs are organized into blocks. Since a block is defined as 4 dwords (16 Bytes), each FIFO is
made up of 512 blocks. Figure 8-1 shows an FIFO example.
The FIFO contains a state machine that is constantly polling the 40 ports to determine if any data is ready
for transfer to/from the FIFO from/to the HDLC engines. The 40 ports are priority decoded with Port 0
getting the highest priority and Port 39 getting the lowest priority. Therefore, all of the enabled HDLC
channels on the lower numbered ports are serviced before the higher numbered ports. As long as the
maximum throughput rate of 132Mbps is not exceeded, the DS3131 ensures that there is enough
bandwidth in this transfer to prevent any data loss between the HDLC engines and the FIFO.
The FIFO also controls which HDLC channel the DMA should service to read data out of the FIFO on
the receive side and to write data into the FIFO on the transmit side. Which channel gets the highest
priority from the FIFO is configurable through some control bits in the Master Configuration (MC)
register (Section 5.2). There are two control bits for the receive side (RFPC0 and RFPC1) and two
control bits for the transmit side (TFPC0 and TFPC1) that will determine the priority algorithm as shown
in Table 8-A. When an HDLC channel is priority decoded, the lower the number of the HDLC channel,
generally the higher the priority. Options 3 and 4 in Table 8-A are exceptions to this rule since they are
priority decoded in reverse order; the round robin decodes in options 3 and 4 are standard with respect to
lower channel numbers receiving higher priority than subsequent channels.
Table 8-A. FIFO Priority Algorithm Select
OPTION
HDLC CHANNELS THAT ARE
PRIORITY DECODED
HDLC CHANNELS THAT ARE SERVICED
ROUND ROBIN
1
None
Decode 1 up to 40
2
Decode 1 to 2
Then 3 up to 40
3
Decode 4, 3, 2, then 1
Then 5 up to 40
4
Decode 16, 15, 14, . . . then 1
Then 17 up to 40
To maintain maximum flexibility for channel reconfiguration, each block within the FIFO can be
assigned to any of the 40 HDLC channels. Also, blocks are link-listed together to form a chain whereby
each block points to the next block in the chain. The minimum size of the link-listed chain is 4 blocks
(64 Bytes) and the maximum is the full size of the FIFO, which is 512 blocks.
To assign a set of blocks to a particular HDLC channel, the host must configure the starting block pointer
and the block pointer RAM. The starting block pointer assigns a particular HDLC channel to a set of
link-listed blocks by pointing to one of the blocks within the chain (it does not matter which block in the
chain is pointed to). The block pointer RAM must be configured for each block that is being used within
the FIFO. The block pointer RAM indicates the next block in the link-listed chain.
Figure 8-1 shows an example of how to configure the starting block pointer and the block pointer RAM.
In this example, only three HDLC channels are being used (channels 2, 6, and 16). The device knows
that channel 2 has been assigned to the eight link-listed blocks of 112, 118, 119, 120, 121, 122, 125, and
126 because a block pointer of 125 has been programmed into the channel 2 position of the starting
相关PDF资料 |
PDF描述 |
|---|---|
| DS3134 | DATACOM, FRAMER, PBGA256 |
| DS3150QN | DATACOM, PCM TRANSCEIVER, PQCC28 |
| DS3150Q | DATACOM, PCM TRANSCEIVER, PQCC28 |
| DS3150TN | DATACOM, PCM TRANSCEIVER, PDIP48 |
| DS3150T | DATACOM, PCM TRANSCEIVER, PQFP48 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS3131DK | 功能描述:通信集成电路 - 若干 RoHS:否 制造商:Maxim Integrated 类型:Transport Devices 封装 / 箱体:TECSBGA-256 数据速率:100 Mbps 电源电压-最大:1.89 V, 3.465 V 电源电压-最小:1.71 V, 3.135 V 电源电流:50 mA, 225 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| DS3134 | 功能描述:IC CTRLR HDLC CHATEAU 256-BGA RoHS:否 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:4,900 系列:- 控制器类型:USB 2.0 控制器 接口:串行 电源电压:3 V ~ 3.6 V 电流 - 电源:135mA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:36-VFQFN 裸露焊盘 供应商设备封装:36-QFN（6x6） 包装:* 其它名称:Q6396337A |
| DS-313PIN | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog Miscellaneous |
| DS-313-PIN | 功能描述:信号调节 RoHS:否 制造商:EPCOS 产品:Duplexers 频率:782 MHz, 751 MHz 频率范围: 电压额定值: 带宽: 阻抗:50 Ohms 端接类型:SMD/SMT 封装 / 箱体:2.5 mm x 2 mm 工作温度范围:- 30 C to + 85 C 封装:Reel |
| DS31400 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:8-Input, 14-Output, Dual DPLL Timing IC with Sub-ps Output Jitter |
发布紧急采购，3分钟左右您将得到回复。