- 您现在的位置：买卖IC网 > PDF目录67723 > ISP1160BD/01,118 (ST-ERICSSON) UNIVERSAL SERIAL BUS CONTROLLER, PQFP64 PDF资料下载
参数资料
| 型号： | ISP1160BD/01,118 |
| 厂商： | ST-ERICSSON |
| 元件分类： | 总线控制器 |
| 英文描述： | UNIVERSAL SERIAL BUS CONTROLLER, PQFP64 |
| 封装： | 10 X 10 MM, 1.40 MM HEIGHT, PLASTIC, MS-026, SOT-314-2, LQFP-64 |
| 文件页数： | 15/88页 |
| 文件大小： | 394K |
| 代理商： | ISP1160BD/01,118 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页
Philips Semiconductors
ISP1160
Embedded USB Host Controller
Product data
Rev. 05 — 24 December 2004
22 of 88
9397 750 13963
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9.4 HC’s internal FIFO buffer RAM structure
9.4.1
Partitions
According to the
Universal Serial Bus Specication Rev. 2.0, there are four types of
USB data transfers: Control, Bulk, Interrupt and Isochronous.
The HC’s internal FIFO buffer RAM has a physical size of 4 kbytes. This internal FIFO
buffer RAM is used for transferring data between the microprocessor and USB
peripheral devices. This on-chip buffer RAM can be partitioned into two areas:
Acknowledged Transfer List (ATL) buffer and Isochronous (ISO) Transfer List (ITL)
buffer. The ITL buffer is a Ping-Pong structured FIFO buffer RAM that is used to keep
the payload data and their PTD header for Isochronous transfers. The ATL buffer is a
non Ping-Pong structured FIFO buffer RAM that is used for the other three types of
transfers.
The ITL buffer can be further partitioned into ITL0 and ITL1 for the Ping-Pong
structure. The ITL0 and ITL1 buffers always have the same size. The microprocessor
can put ISO data into either the ITL0 buffer or the ITL1 buffer. When the
microprocessor accesses an ITL buffer, the HC can take over the other ITL buffer at
the same time. This architecture improves the ISO transfer performance.
The HCD can assign the logical size for the ATL buffer and ITL buffers at any time, but
normally at initialization after power-on reset. This is done by setting the
HcATLBufferLength register (2BH to read, ABH to write) and the HcITLBufferLength
register (2AH to read, AAH to write), respectively. The total length (ATL buffer
+ ITL
buffer) should not exceed the maximum RAM size of 4 kbytes. Figure 17 shows the
partitions of the internal FIFO buffer RAM. When assigning buffer RAM sizes, follow
this formula:
ATL buffer length
+ 2 × (ITL buffer size) ≤ 1000H (that is, 4 kbytes)
where: ITL buffer size
= ITL0 buffer length = ITL1 buffer length
The following assignments are examples of legal uses of the internal FIFO buffer
RAM:
ATL buffer length
= 800H, ITL buffer length = 400H.
This is the maximum use of the internal FIFO buffer RAM.
DirectionPID[1:0]
R
00
SETUP
01
OUT
10
IN
11
reserved
B5_5
R/W
This bit is logic 0 at power-on reset. When this feature is not used, software used for the
ISP1160 is the same for the ISP1161 and the ISP1161A. When this bit is set to logic 1 in
this PTD for interrupt endpoint transfer, only one PTD USB transaction will be sent out in
1ms.
Format
R
The format of this data structure. If this is a Control, Bulk or Interrupt endpoint, then
Format
= 0. If this is an Isochronous endpoint, then Format = 1.
FunctionAddress[6:0]
R
This is the USB address of the function containing the endpoint that this PTD refers to.
Table 5:
Philips Transfer Descriptor (PTD): bit description…continued
Symbol
Access
Description
相关PDF资料 |
PDF描述 |
|---|---|
| ISP1160BD/01,151 | UNIVERSAL SERIAL BUS CONTROLLER, PQFP64 |
| ISP1161A1BM,557 | UNIVERSAL SERIAL BUS CONTROLLER, PQFP64 |
| ISP1181BBS,551 | UNIVERSAL SERIAL BUS CONTROLLER, PQCC48 |
| ISP1181BBS,518 | UNIVERSAL SERIAL BUS CONTROLLER, PQCC48 |
| ISP1181BDGG,112 | UNIVERSAL SERIAL BUS CONTROLLER, PDSO48 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISP1160BD01FA | 功能描述:IC USB HOST CONTROLLER 64LQFP RoHS:是 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:4,900 系列:- 控制器类型:USB 2.0 控制器 接口:串行 电源电压:3 V ~ 3.6 V 电流 - 电源:135mA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:36-VFQFN 裸露焊盘 供应商设备封装:36-QFN（6x6） 包装:* 其它名称:Q6396337A |
| ISP1160BD01-S | 功能描述:USB 接口集成电路 USB FULL SPEED HOST RoHS:否 制造商:Cypress Semiconductor 产品:USB 2.0 数据速率: 接口类型:SPI 工作电源电压:3.15 V to 3.45 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:WLCSP-20 |
| ISP1160BD01-T | 功能描述:USB 接口集成电路 USB HOST CTRL FULL-SPD RoHS:否 制造商:Cypress Semiconductor 产品:USB 2.0 数据速率: 接口类型:SPI 工作电源电压:3.15 V to 3.45 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:WLCSP-20 |
| ISP1160BD01TM | 功能描述:IC USB HOST CTRL FULL-SPD 64LQFP RoHS:是 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:4,900 系列:- 控制器类型:USB 2.0 控制器 接口:串行 电源电压:3 V ~ 3.6 V 电流 - 电源:135mA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:36-VFQFN 裸露焊盘 供应商设备封装:36-QFN（6x6） 包装:* 其它名称:Q6396337A |
| ISP1160BM | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Embedded Universal Serial Bus Host Controller |
发布紧急采购，3分钟左右您将得到回复。