参数资料
型号: ISP1160BD/01,118
厂商: ST-ERICSSON
元件分类: 总线控制器
英文描述: UNIVERSAL SERIAL BUS CONTROLLER, PQFP64
封装: 10 X 10 MM, 1.40 MM HEIGHT, PLASTIC, MS-026, SOT-314-2, LQFP-64
文件页数: 18/88页
文件大小: 394K
代理商: ISP1160BD/01,118
Philips Semiconductors
ISP1160
Embedded USB Host Controller
Product data
Rev. 05 — 24 December 2004
25 of 88
9397 750 13963
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
9.4.3
Operation and C program example
Figure 20 shows the block diagram for internal FIFO buffer RAM operations in the
PIO mode. The ISP1160 provides one register as the access port for each buffer
RAM. For the ITL buffer RAM, the access port is the ITLBufferPort register (40H to
read, C0H to write). For the ATL buffer RAM, the access port is the ATLBufferPort
register (41H to read, C1H to write). The buffer RAM is an array of bytes (8 bits) while
the access port is a 16-bit register. Therefore, each read/write operation on the port
accesses two consecutive memory locations, incrementing the pointer of the internal
buffer RAM by two.
The lower byte of the access port register corresponds to the data byte at the even
location of the buffer RAM, and the upper byte corresponds to the next data byte at
the odd location of the buffer RAM. Regardless of the number of data bytes to be
transferred, the command code must be issued merely once, and it will be followed by
a number of accesses of the data port (see Section 8.4).
When the pointer of the buffer RAM reaches the value of the HcTransferCounter
register, an internal EOT signal will be generated to set bit 2, AllEOTInterrupt, of the
Hc
PInterrupt register and update the HcBufferStatus register, to indicate that the
whole data transfer has been completed.
For ITL buffer RAM, every start of frame (SOF) signal (1 ms) will cause toggling
between ITL0 and ITL1 but this depends on the buffer status. If both ITL0BufferFull
and ITL1BufferFull of the HcBufferStatus register are already logic 1, meaning that
both ITL0 and ITL1 buffer RAMs are full, the toggling will not happen. In this case, the
microprocessor will always have access to ITL1.
Fig 19. PTD data with DWORD alignment in buffer RAM.
MGT953
payload data
(14 bytes)
PTD
(8 bytes)
PTD
(8 bytes)
00H
top
08H
15H
18H
20H
payload data
RAM buffer
相关PDF资料
PDF描述
ISP1160BD/01,151 UNIVERSAL SERIAL BUS CONTROLLER, PQFP64
ISP1161A1BM,557 UNIVERSAL SERIAL BUS CONTROLLER, PQFP64
ISP1181BBS,551 UNIVERSAL SERIAL BUS CONTROLLER, PQCC48
ISP1181BBS,518 UNIVERSAL SERIAL BUS CONTROLLER, PQCC48
ISP1181BDGG,112 UNIVERSAL SERIAL BUS CONTROLLER, PDSO48
相关代理商/技术参数
参数描述
ISP1160BD01FA 功能描述:IC USB HOST CONTROLLER 64LQFP RoHS:是 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:4,900 系列:- 控制器类型:USB 2.0 控制器 接口:串行 电源电压:3 V ~ 3.6 V 电流 - 电源:135mA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:36-VFQFN 裸露焊盘 供应商设备封装:36-QFN(6x6) 包装:* 其它名称:Q6396337A
ISP1160BD01-S 功能描述:USB 接口集成电路 USB FULL SPEED HOST RoHS:否 制造商:Cypress Semiconductor 产品:USB 2.0 数据速率: 接口类型:SPI 工作电源电压:3.15 V to 3.45 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:WLCSP-20
ISP1160BD01-T 功能描述:USB 接口集成电路 USB HOST CTRL FULL-SPD RoHS:否 制造商:Cypress Semiconductor 产品:USB 2.0 数据速率: 接口类型:SPI 工作电源电压:3.15 V to 3.45 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:WLCSP-20
ISP1160BD01TM 功能描述:IC USB HOST CTRL FULL-SPD 64LQFP RoHS:是 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:4,900 系列:- 控制器类型:USB 2.0 控制器 接口:串行 电源电压:3 V ~ 3.6 V 电流 - 电源:135mA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:36-VFQFN 裸露焊盘 供应商设备封装:36-QFN(6x6) 包装:* 其它名称:Q6396337A
ISP1160BM 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Embedded Universal Serial Bus Host Controller