参数资料
| 型号： | MC34708VM |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 37/159页 |
| 文件大小： | 0K |
| 描述： | IC POWER MANAGEMENT 206MAPBGA |
| 标准包装： | 160 |
| 应用： | 通用 |
| 电源电压： | 1.8 V ~ 4.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 206-LFBGA |
| 供应商设备封装： | 206-MAPBGA（13x13） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页当前第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页
Functional Block Description
The following are text descriptions of the power states of the system for additional details of the state machine to complement
the drawing in Figure 6 . Note that the SPI control is only possible in the Watchdog, On and User Off Wait states and the interrupt
line INT is kept low in all states except for Watchdog and On.
7.5.2.1
Coin Cell
The RTC module is powered from either the battery or the coin cell, due to insufficient voltage at VALWAYS, and the IC is not in
a Power Cut. No Turn On event is accepted in the Coin Cell state. Transition out (to the Off state) requires VALWAYS restoration
with a threshold above UVDET. RESETB and RESETBMCU are held low in this mode.
The RTC module remains active (32 kHz oscillator + RTC timers), along with VALWAYS level detection to qualify exit to the Off
state. VCOREDIG is off and the VDDLP regulator is on, the rest of the system is put into its lowest power configuration.
If the coin cell is depleted (VSTRC drops to 0.9 - 0.8 V while in the Coin Cell state), a complete system reset will occur. At next
power application / Turn On event, the system will startup reinitialized with all SPI bits including those that reset on RTCPORB
restored to their default states.
7.5.2.2
Off (with good battery)
If the supply VALWAYS is above the UVDET threshold, only the IC core circuitry at VCOREDIG and the RTC module are
powered, all other supplies are inactive. To exit the Off state, a valid turn on event is required. No specific timer is running in this
state. RESETB, RESETBMCU are held low in this state.
If the supply VALWAYS is below the UVDET threshold, no turn on events are accepted. If a valid coin cell is present, the core
gets powered from LICELL. The only active circuitry is the RTC module and the VCORE module powering VCOREDIG at 1.5 V.
7.5.2.3
Cold Start
Cold Start is entered upon a Turn On event from Off, Warm Boot, successful PCUT, or a Silent System Restart. The first 8.0 ms
is used for initialization which includes bias generation, PUMSx configuration latching, and qualification of the input supply level
BP. The switching and linear regulators are then powered up sequentially to limit the inrush current; see the Power Up section
for sequencing and default level details. The reset signals RESETB and RESETBMCU are kept low. The Reset timer starts
running when entering Cold Start. The Cold Start state is exited for the Watchdog state and both RESETB and RESETBMCU
become high (open drain output with external pull-ups) when the reset timer expires. The input control pins WDI, and STANDBY
are ignored.
7.5.2.4
Watchdog
The system is fully powered and under SPI/I 2 C control. RESETB and RESETBMCU are high. The Watchdog timer starts running
when entering the Watchdog state. When expired, the system transitions to the On state, where WDI will be checked and
monitored. The input control pins WDI and STANDBY are ignored while in the Watchdog state.
7.5.2.5
On Mode
The system is fully powered and under SPI control. RESETB and RESETBMCU are high. The WDI pin must be high to stay in
this state. The WDI IO supply voltage is referenced to SPIVCC (normally connected to SW5 = 1.8 V); SPIVCC must therefore
remain enabled to allow for proper WDI detection. If WDI goes low, the system will transition to the Off state or Cold Start
(depending on the configuration; refer to the section on Silent System Restart with WDI Event for details).
7.5.2.6
User Off Wait
The system is fully powered and under SPI control. The WDI pin no longer has control over the part. The Wait mode is entered
by a processor request for user off by setting the USEROFFSPI bit high. This is normally initiated by the end user via the power
key; upon receiving the corresponding interrupt, the system will determine if the product has been configured for User Off or
Memory Hold states (both of which first require passing through User Off Wait) or just transition to Off.
The Wait timer starts running when entering User Off Wait state. This leaves the processor time to suspend or terminate its tasks.
When expired, the Wait state is exited for User Off state or Memory Hold state depending on warm starts being enabled or not
via the WARMEN bit. The USEROFFSPI bit is being reset at this point by RESETB going low.
MC34708
Analog Integrated Circuit Device Data ?
37
Freescale Semiconductor
相关PDF资料 |
PDF描述 |
|---|---|
| MC34710EWR2 | IC PWR SUPPLY ADJ DUAL SW 32SOIC |
| MC34712EPR2 | IC CONVERTER DDR 24QFN |
| MC34713EPR2 | IC CONVERTER DDR 24QFN |
| MC34716EPR2 | IC CONVERTER DDR 26QFN |
| MC34717EPR2 | IC CONVERTER DDR 26QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC34708VMR2 | 功能描述:PMIC 解决方案 PMIC 5S 6LDO BST 10BTADC RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MC34709 | 制造商:SPC Multicomp 功能描述:HEADER R/ANGLE 12WAY 制造商:SPC Multicomp 功能描述:HEADER, R/ANGLE, 12WAY 制造商:SPC Multicomp 功能描述:WIRE-BOARD CONN, RECEPTACLE, 12POS, 3MM; Series:2261(5561); Pitch Spacing:3mm; Contact Termination:Through Hole Right Angle; No. of Contacts:12; No. of Rows:2; Connector Mounting:PCB; Gender:Receptacle; Contact Material:Copper Alloy ;RoHS Compliant: Yes |
| MC34709VK | 功能描述:PMIC 解决方案 PMIC 5SW, 6 LDO BST, 10 Bit ADC RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MC34709VKR2 | 功能描述:PMIC 解决方案 PMIC 5SW, 6 LDO BST, 10 Bit ADC RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MC3470N | 制造商:Texas Instruments 功能描述: |
发布紧急采购，3分钟左右您将得到回复。