参数资料
| 型号： | MC34708VM |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 99/159页 |
| 文件大小： | 0K |
| 描述： | IC POWER MANAGEMENT 206MAPBGA |
| 标准包装： | 160 |
| 应用： | 通用 |
| 电源电压： | 1.8 V ~ 4.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 206-LFBGA |
| 供应商设备封装： | 206-MAPBGA（13x13） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页当前第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页
Functional Block Description
7.8.4.9
JiG Cable USB and UART
The JIG cable is used for test and development and has an ID resistance to differentiate it from a regular USB cable. The Jig
cable has 2 ID resistance values to resemble a USB JIG type1/2, and 2 ID resistance values to resemble a UART JIG type1/2
cable.
7.8.4.9.1
USB JIG Cable 1 or 2
Under normal operation, setting the control bits when the identified accessory is a USB JIG 1 or 2 cable, both the DPLUS to DP,
the DMINUS to DM switches are switched on.
When SW_HOLD = 0, the switching action of DPLUS to DP, and the DMINUS to DM switches are controlled by the WAIT bit. If
WAIT = 1, the signal switches will be turned ON after a WAIT. If WAIT = 0, the signal switches won't be turned on until the WAIT
bit is set to '1' by the SPI/I 2 C. When SW_HOLD = 1, regardless of what the WAIT is set to, '0' or '1', the signal switches are turned
on, once the USB JIG cable is identified.
The ID detector and the VBUS detector both monitor the detachment of the USB JIG cable. The ID detection circuit continues to
be ON for detachment detection in the Active mode. When the ID_FLOAT is set, the Detach bit in the Interrupt Status 0 register
is set to inform the host. When the USBDETS is set to '0', which means either the VBUS power is removed or the cable is
detached, the Detach bit is also set to inform the host. The mini USB interface moves to the Standby mode. If the Detach bit is
set, due to the removing only the VBUS or the ID resistance, and the cable is not detached completely, the identification flow will
be triggered again. The ID_FLOAT bit or USBDETS bit still indicate an accessory is connected when the mini USB interface
moves to the Standby mode. All the signal switches are turned off
7.8.4.9.2
UART JIG Cable 1 or 2
Under normal operation, setting the control bits when the identified accessory is a UART JIG cable 1 or 2, both the RxD to DP
and the TxD to DM switches are switched on.
When SW_HOLD = 0, the switching action of RxD to DP, and the TxD to DM switches, are controlled by the WAIT bit. If WAIT = 1,
the signal switches will be turned on after a WAIT time. If WAIT = 0, the signal switches won't be turned on until the WAIT bit is
set to '1' by the SPI/I 2 C. When SW_HOLD = 1, regardless of what the WAIT is set to, '0' or '1', the signal switches are turned on,
once the UART JIG cable is identified.
The ID detection comparator continues to be ON for detachment detection in the Active mode. When the ID_FLOAT is set, the
Detach bit in the Interrupt Status 0 register is set to inform the host the accessory is detached. The mini USB interface then enters
the Standby mode.
7.8.4.10
TTY Operation Mode
A TTY converter is a type of audio accessory. It has its own ID resistance. When a TTY converter is attached, this sets the TTY
bit in the USB Device Type register and the Attach interrupt bit in the Interrupt Status 0 register. During normal operation, when
setting the control bits, the automatic switch configuration of the TTY converter, is similar to that of an Audio Type 1 accessory.
The SPK_R to DP switch, and MIC to VBUS switch are turned on, but the SPK_L to DM switch can only be turned on when
TTY_SKPL bit in USB Control register is manually set to 1. In addition, the MOTG, and M0 switches are turned off to isolate the
VBUS pin.The TTY accessory doesn’t support the remote control key. The Power Save mode operation and the detachment
detection are the same as those of the Audio Type 1 device.
7.8.4.11
UART Operation Mode
During normal operation, when setting the control bits, when the identified accessory is a UART cable, both the RxD and the TxD
switches are switched on (see Figure 30 ).
The ID detection comparator continues to be ON for detachment detection in the Active mode. When the ID_FLOAT is set, the
Detach bit in the USB interrupt Sense register, is set to inform the host the accessory is detached. The MC34708 USB detection
then enters Standby mode.
MC34708
Analog Integrated Circuit Device Data ?
99
Freescale Semiconductor
相关PDF资料 |
PDF描述 |
|---|---|
| MC34710EWR2 | IC PWR SUPPLY ADJ DUAL SW 32SOIC |
| MC34712EPR2 | IC CONVERTER DDR 24QFN |
| MC34713EPR2 | IC CONVERTER DDR 24QFN |
| MC34716EPR2 | IC CONVERTER DDR 26QFN |
| MC34717EPR2 | IC CONVERTER DDR 26QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC34708VMR2 | 功能描述:PMIC 解决方案 PMIC 5S 6LDO BST 10BTADC RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MC34709 | 制造商:SPC Multicomp 功能描述:HEADER R/ANGLE 12WAY 制造商:SPC Multicomp 功能描述:HEADER, R/ANGLE, 12WAY 制造商:SPC Multicomp 功能描述:WIRE-BOARD CONN, RECEPTACLE, 12POS, 3MM; Series:2261(5561); Pitch Spacing:3mm; Contact Termination:Through Hole Right Angle; No. of Contacts:12; No. of Rows:2; Connector Mounting:PCB; Gender:Receptacle; Contact Material:Copper Alloy ;RoHS Compliant: Yes |
| MC34709VK | 功能描述:PMIC 解决方案 PMIC 5SW, 6 LDO BST, 10 Bit ADC RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MC34709VKR2 | 功能描述:PMIC 解决方案 PMIC 5SW, 6 LDO BST, 10 Bit ADC RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MC3470N | 制造商:Texas Instruments 功能描述: |
发布紧急采购，3分钟左右您将得到回复。