参数资料
| 型号： | MC34708VM |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 45/159页 |
| 文件大小： | 0K |
| 描述： | IC POWER MANAGEMENT 206MAPBGA |
| 标准包装： | 160 |
| 应用： | 通用 |
| 电源电压： | 1.8 V ~ 4.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 206-LFBGA |
| 供应商设备封装： | 206-MAPBGA（13x13） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页当前第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页
Functional Block Description
7.5.4
Buck Switching Regulators
Six buck switching regulators are provided with integrated power switches and synchronous rectification. In a typical application,
SW1 and SW2 are used for supplying the application processor core power domains. Split power domains allow independent
DVS control for processor power optimization, or to support technologies with a mix of device types with different voltage ratings.
SW3 is used for powering internal processor memory as well as low voltage peripheral devices and interfaces which can run at
the same voltage level. SW4A/B is used for powering external DDR memory as well as low voltage peripheral devices and
interfaces, which can run at the same voltage level. SW5 is used to supply the I/O domain for the system.
The buck regulators are supplied from the system supply BP, which is drawn from the main battery or the external battery charger
(when present).
The switching regulators can operate in different modes depending on the load conditions. These modes can be set through the
SPI/I 2 C and include a PFM mode, an Automatic Pulse Skipping mode (APS), and a PWM mode. The previous selection is
optimized to maximum battery life based on load conditions.
Table 31. Buck Operating Modes
Mode
OFF
PFM
APS
PWM
Description
The regulator is switched off and the output voltage is discharged
The regulator is switched on and set to PFM mode operation. In this mode, the regulator
is always running in PFM mode. Useful at light loads for optimized efficiency.
The regulator is switched on and set to Automatic Pulse Skipping. In this mode the
regulator moves automatically between pulse skipping and full PWM mode depending
on load conditions.
The regulator is switched on and set to PWM mode. In this mode the regulator is always
in full PWM mode operation regardless of load conditions.
Buck modes of operation are programmable for explicitly defined or load-dependent control.
During soft-start of the buck regulators, the controller transitions through the PFM, APS, and PWM switching modes. 3.0 ms
(typical) after the output voltage reaches regulation, the controller transitions to the selected switching mode. Depending on the
particular switching mode selected, additional ripple may be observed on the output voltage rail as the controller transitions
between switching modes. The regulators are turned on in APS mode by default. After the start-up sequence is complete, all
switching regulators should be set to PFM/PWM mode, depending on system load for best performance.
Point of load feedback is intended for minimizing errors due to board level IR drops.
7.5.4.1
General Control
Operational modes of the Buck regulators can be controlled by direct SPI programming, altered by the state of the STANDBY
pin, by direct state machine influence (entering Off or low power Off states, for example), or by load current magnitude when so
configured (APS mode). Available modes include PWM, PFM, APS and OFF. For light loading, the regulators should be put into
PFM mode to optimize efficiency.
Provisions are made for maintaining PFM operation in User off and Memhold modes, to support state retention for faster startup
from the Low Power Off modes for Warm Start or Warm Boot. SWxMODE[3:0] bits will be reset to their default values defined by
PUMSx settings by the startup sequencer.
Table 32 summarizes the Buck regulators programmability for Normal and Standby modes.
Table 32. Switching regulator Mode Control for Normal and Standby Operation
SWxMODE[3:0]
0000
0001
0010
0011
Normal Mode
Off
PWM
Reserved
PFM
Standby Mode
Off
Off
Reserved
Off
MC34708
Analog Integrated Circuit Device Data ?
45
Freescale Semiconductor
相关PDF资料 |
PDF描述 |
|---|---|
| MC34710EWR2 | IC PWR SUPPLY ADJ DUAL SW 32SOIC |
| MC34712EPR2 | IC CONVERTER DDR 24QFN |
| MC34713EPR2 | IC CONVERTER DDR 24QFN |
| MC34716EPR2 | IC CONVERTER DDR 26QFN |
| MC34717EPR2 | IC CONVERTER DDR 26QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC34708VMR2 | 功能描述:PMIC 解决方案 PMIC 5S 6LDO BST 10BTADC RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MC34709 | 制造商:SPC Multicomp 功能描述:HEADER R/ANGLE 12WAY 制造商:SPC Multicomp 功能描述:HEADER, R/ANGLE, 12WAY 制造商:SPC Multicomp 功能描述:WIRE-BOARD CONN, RECEPTACLE, 12POS, 3MM; Series:2261(5561); Pitch Spacing:3mm; Contact Termination:Through Hole Right Angle; No. of Contacts:12; No. of Rows:2; Connector Mounting:PCB; Gender:Receptacle; Contact Material:Copper Alloy ;RoHS Compliant: Yes |
| MC34709VK | 功能描述:PMIC 解决方案 PMIC 5SW, 6 LDO BST, 10 Bit ADC RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MC34709VKR2 | 功能描述:PMIC 解决方案 PMIC 5SW, 6 LDO BST, 10 Bit ADC RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MC3470N | 制造商:Texas Instruments 功能描述: |
发布紧急采购，3分钟左右您将得到回复。