- 您现在的位置：买卖IC网 > PDF目录69029 > MC68HCP11A1CFNE3 (MOTOROLA INC) 8-BIT, EEPROM, 3 MHz, MICROCONTROLLER, PQCC52 PDF资料下载
参数资料
| 型号： | MC68HCP11A1CFNE3 |
| 厂商： | MOTOROLA INC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, EEPROM, 3 MHz, MICROCONTROLLER, PQCC52 |
| 封装： | PLASTIC, LCC-52 |
| 文件页数： | 95/158页 |
| 文件大小： | 776K |
| 代理商： | MC68HCP11A1CFNE3 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页当前第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页
MC68HC11A8
PARALLEL I/O
MOTOROLA
TECHNICAL DATA
4-3
4
4.4.1 Input Handshake Protocol
In the input handshake protocol, port C is a latching input port, STRA is an edge-sen-
sitive latch command from the external system that is driving port C, and STRB is a
“ready” output line controlled by logic in the MCU.
When a “ready” condition is recognized, the external device places data on the port C
lines, then pulses the STRA line. The active edge on the STRA line latches the port C
data into the PORTCL register, sets the STAF flag (optionally causing an interrupt),
and deasserts the STRB line. Deassertion of the STRB line automatically inhibits the
external device from strobing new data into port C. Reading the PORTCL latch register
(independent of clearing the STAF flag) asserts the STRB line, indicating that new
data may now be applied to port C.
The STRB line can be configured (with the PLS control bit) to be a pulse output (pulse
mode) or a static output (interlocked mode).
The port C data direction register bits should be cleared for each line that is to be used
as a latched input line. However, some port C lines can be used as latched inputs with
the input handshake protocol while, at the same time, using some port C lines as static
inputs, and some port C lines as static outputs. The input handshake protocol has no
effect on the use of port C lines as static inputs or as static outputs. Reads of the
PORTC data register always return the static logic level at the port C lines (for lines
configured as inputs). Writes to either the PORTC data register or the alternate latched
port C register (PORTCL) send information to the same port C output register without
affecting the input handshake strobes.
4.4.2 Output Handshake Protocol
In the output handshake protocol, port C is an output port, STRB is a “ready” output,
and STRA is an edge-sensitive acknowledge input signal, used to indicate to the MCU
that the output data has been accepted by the external device. In a variation of this
output handshake protocol, STRA is also used as an output-enable input, as well as
an edge-sensitive acknowledge input.
The MCU places data on the port C output lines and then indicates stable data is avail-
able by asserting the STRB line. The external device then processes the available
data and pulses the STRA line to indicate that new data may be placed on the port C
output lines. The active edge on the STRA line causes the STRB line to be deasserted
and the STAF status flag to be set. In response to the STAF bit being set, the program
transfers new data out of port C as required. Writing data to the PORTCL register
causes the data to appear on port C lines and asserts the STRB line.
There is a variation to the output handshake protocol that allows three-state operation
on port C. It is possible to directly connect this 8-bit parallel port to other three-state
devices with no additional parts.
While the STRA input line is inactive, all port C lines obey the data direction specified
by the data direction register so that lines which are configured as inputs are high im-
pedance. When the STRA line is activated, all port C lines are forced to outputs re-
gardless of the data in the data direction register. Note that in output handshake
相关PDF资料 |
PDF描述 |
|---|---|
| MC68HLC705KJ1C | 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PDIP16 |
| MC68HRC08JK1CDW | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PDSO20 |
| MC68HC08JK1CP | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PDIP20 |
| MC68HC08JK1CDW | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PDSO20 |
| MC68HC08JK3MDW | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO20 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MC68HCP11A1FN | 制造商:MOTORALA 功能描述: |
| MC68HCP11E0CP2 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| MC68HCP11E0FN | 功能描述:MICROCONTROLLER MCU 8ADC 3MHC RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:HC11 标准包装:250 系列:56F8xxx 核心处理器:56800E 芯体尺寸:16-位 速度:60MHz 连通性:CAN，SCI，SPI 外围设备:POR，PWM，温度传感器，WDT 输入/输出数:21 程序存储器容量:40KB（20K x 16） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:6K x 16 电压 - 电源 (Vcc/Vdd):2.25 V ~ 3.6 V 数据转换器:A/D 6x12b 振荡器型:内部 工作温度:-40°C ~ 125°C 封装/外壳:48-LQFP 包装:托盘 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323 |
| MC68HCP11E0FNE | 功能描述:8位微控制器 -MCU 8B MCU 512RAM COP A/D RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| MC68HCP11E1CFNE2 | 功能描述:8位微控制器 -MCU 8B MCU 512 BYTES RAM RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。