参数资料
型号: MC8640DHX1250HE
厂商: FREESCALE SEMICONDUCTOR INC
元件分类: 微控制器/微处理器
英文描述: 32-BIT, 1250 MHz, MICROPROCESSOR, CBGA1023
封装: 33 X 33 MM, CERAMIC, FCBGA-1023
文件页数: 28/130页
文件大小: 1495K
代理商: MC8640DHX1250HE
MPC8640 and MPC8640D Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
123
System Design Information
The COP interface has a standard header, shown in Figure 67, for connection to the target system, and is
based on the 0.025" square-post, 0.100" centered header assembly (often called a Berg header). The
connector typically has pin 14 removed as a connector key.
The COP header adds many benefits such as breakpoints, watchpoints, register and memory
examination/modification, and other standard debugger features. An inexpensive option can be to leave
the COP header unpopulated until needed.
There is no standardized way to number the COP header shown in Figure 67; consequently, many different
pin numbers have been observed from emulator vendors. Some are numbered top-to-bottom then
left-to-right, while others use left-to-right then top-to-bottom, while still others number the pins counter
clockwise from pin 1 (as with an IC). Regardless of the numbering, the signal placement recommended in
Figure 67 is common to all known emulators.
For a multi-processor non-daisy chain configuration, Figure 68, can be duplicated for each processor. The
recommended daisy chain configuration is shown in Figure 69. Please consult with your tool vendor to
determine which configuration is supported by their emulator.
20.9.1 Termination of Unused Signals
If the JTAG interface and COP header will not be used, Freescale recommends the following connections:
TRST should be tied to HRESET through a 0 k
Ω isolation resistor so that it is asserted when the
system reset signal (HRESET) is asserted, ensuring that the JTAG scan chain is initialized during
the power-on reset flow. Freescale recommends that the COP header be designed into the system
as shown in Figure 68. If this is not possible, the isolation resistor will allow future access to TRST
in case a JTAG interface may need to be wired onto the system in future debug situations.
Tie TCK to OVDD through a 10 kΩ resistor. This will prevent TCK from changing state and
reading incorrect data into the device.
No connection is required for TDI, TMS, or TDO.
Figure 67. COP Connector Physical Pinout
3
13
9
5
1
6
10
15
11
7
16
12
8
4
KEY
No pin
1
2
COP_TDO
COP_TDI
NC
COP_TRST
COP_VDD_SENSE
COP_CHKSTP_IN
NC
GND
COP_TCK
COP_TMS
COP_SRESET
COP_HRESET
COP_CHKSTP_OUT
相关PDF资料
PDF描述
MC8640DHX1067NC 32-BIT, 1067 MHz, MICROPROCESSOR, CBGA1023
MC8640DTVU1000HE 32-BIT, 1000 MHz, MICROPROCESSOR, CBGA1023
MC8640DTHX1067NC 32-BIT, 1067 MHz, MICROPROCESSOR, CBGA1023
MC8640THX1250HC 32-BIT, 1250 MHz, MICROPROCESSOR, CBGA1023
MC8640DTVU1250HE 32-BIT, 1250 MHz, MICROPROCESSOR, CBGA1023
相关代理商/技术参数
参数描述
MC8640DHX1250N 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Integrated Host Processor Hardware Specifications Addendum for the MC8640xTxxyyyyaC Series
MC8640DTHX1000H 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Integrated Host Processor Hardware Specifications
MC8640DTHX1000HC 功能描述:微处理器 - MPU G8 REV2.1 1.05V -40/105C RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324
MC8640DTHX1000HE 功能描述:微处理器 - MPU G8 REV 3.0 1.05V -40/105C RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324
MC8640DTHX1000N 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Integrated Host Processor Hardware Specifications Addendum for the MC8640xTxxyyyyaC Series