- 您现在的位置：买卖IC网 > Datasheet目录476 > MCP2030A-I/P (Microchip Technology)IC KEYLESS ENTRY AFE 3CH 14PDIP Datasheet资料下载
参数资料
| 型号： | MCP2030A-I/P |
| 厂商： | Microchip Technology |
| 文件页数： | 31/66页 |
| 文件大小： | 0K |
| 描述： | IC KEYLESS ENTRY AFE 3CH 14PDIP |
| 标准包装： | 30 |
| RF 型： | PEG，TPMS |
| 频率： | 125kHz |
| 特点： | 4 通道 |
| 封装/外壳： | 14-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 14-PDIP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页当前第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页
MCP2030
5.0
FUNCTIONAL DESCRIPTION
The modulation data comes from the external micro-
AND THEORY OF DEVICE
OPERATION
The MCP2030 contains three analog input channels for
signal detection and LF talk-back. This section
provides the function description of the device.
Each analog input channel has internal tuning
controller section via the digital SPI as “Clamp On”,
“Clamp Off” commands. Only those inputs that are
enabled will execute the Clamp command. A basic
block diagram of the modulation circuit is shown in
Figure 5-1 and Figure 5-2.
The modulation FET is also shorted momentarily after
Soft Reset and Inactivity timer time-out.
capacitors, sensitivity control circuits, an input signal
strength limiter and an LF talk-back modulation
5.3
Tuning Capacitor
transistor. An Automatic Gain Control (AGC) loop is
used for all three input channel gains. The output of
each channel is OR’d and fed into a demodulator. The
digital output is passed to the LFDATA pin. Figure 5-1
Each channel has internal tuning capacitors for external
antenna tuning. The capacitor values are programmed
by the Configuration registers up to 63 pF, 1 pF per step.
shows the block diagram of the device and Figure 5-2
shows the input signal path.
There are a total of eight Configuration registers. Six of
them are used for device operation options, one for
column parity bits and one for status indication of
device operation. Each register has 9 bits including one
Note:
5.4
The user can control the tuning capaci-
tor by programming the Configuration
registers. See Register 5-2 through
Register 5-4 for details.
Variable Attenuator
row parity bit. These registers are readable and
writable by SPI commands except for the STATUS
register, which is read-only.
The variable attenuator is used to attenuate, via AGC
control, the input signal voltage to avoid saturating the
amplifiers and demodulators.
The device’s features are dynamically controllable by
programming the Configuration registers.
Note:
The variable attenuator function is
accomplished by the device itself. The
5.1
RF Limiter
user cannot control its function.
The RF Limiter limits LC pin input voltage by de-Q’ing
the external LC resonant antenna circuit. The limiter
5.5
Sensitivity Control
begins de-Q’ing the external LC antenna when the
input voltage exceeds V DE_Q , progressively de-Q’ing
harder to reduce the antenna input voltage.
The sensitivity of each channel can be reduced by the
channel’s Configuration register sensitivity setting.
This is used to desensitize the channel from optimum.
The signal levels from all 3 channels are combined
such that the limiter attenuates all 3 channels
uniformly, in respect to the channel with the strongest
signal.
Note:
The user can desensitize the channel
sensitivity by programming the
Configuration registers. See Register 5-5
and Register 5-6 for details.
5.2
Modulation Circuit
5.6
AGC Control
The modulation circuit consists of a modulation
transistor (FET), internal tuning capacitors and external
LC antenna components. The modulation transistor
and the internal tuning capacitors are connected
between the LC input pin and LCCOM pin. Each LC
input has its own modulation transistor.
When the modulation transistor turns on, its low Turn-
The AGC controls the variable attenuator to limit the
internal signal voltage to avoid saturation of internal
amplifiers and demodulators (Refer to Section 5.4
“Variable Attenuator” ).
The signal levels from all 3 channels are combined
such that the AGC attenuates all 3 channels uniformly
in respect to the channel with the strongest signal.
on Resistance (R M ) clamps the induced LC antenna
voltage. The coil voltage is minimized when the
modulation transistor turns-on and maximized when
the modulation transistor turns-off. The modulation
transistor ’s low turn-on resistance (R M ) results in a high
modulation depth.
The LF talk-back is achieved by turning on and off the
modulation transistor.
? 2005 Microchip Technology Inc.
Note:
The AGC control function is accomplished
by the device itself. The user cannot
control its function.
DS21981A-page 31
相关PDF资料 |
PDF描述 |
|---|---|
| MCP2030DM-TPR | BOARD DEMO PICTAIL MCP2030 |
| MCP9502PT-095E/OT | IC TEMP SWITCH PROGR P-P SOT23-5 |
| MCP9510CT-E/CH | IC TEMP SWITCH OD 125C SOT23-6 |
| MD7IC18120NR1 | IC PWR AMP RF LDMOS TO270-16 |
| MDEV-315-HH-KF-MS | KIT MASTER DEV MS KEYFOB 315MHZ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP2030AT-I/SL | 功能描述:射频无线杂项 Keyless Entry AFE RoHS:否 制造商:Texas Instruments 工作频率:112 kHz to 205 kHz 电源电压-最大:3.6 V 电源电压-最小:3 V 电源电流:8 mA 最大功率耗散: 工作温度范围:- 40 C to + 110 C 封装 / 箱体:VQFN-48 封装:Reel |
| MCP2030AT-I/ST | 功能描述:射频无线杂项 Keyless Entry AFE RoHS:否 制造商:Texas Instruments 工作频率:112 kHz to 205 kHz 电源电压-最大:3.6 V 电源电压-最小:3 V 电源电流:8 mA 最大功率耗散: 工作温度范围:- 40 C to + 110 C 封装 / 箱体:VQFN-48 封装:Reel |
| MCP2030DM-TPR | 功能描述:射频开发工具 MCP9800 Thermal Snsr PICtail Demo Brd RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| MCP2030-I/P | 功能描述:射频无线杂项 Keyless Entry AFE RoHS:否 制造商:Texas Instruments 工作频率:112 kHz to 205 kHz 电源电压-最大:3.6 V 电源电压-最小:3 V 电源电流:8 mA 最大功率耗散: 工作温度范围:- 40 C to + 110 C 封装 / 箱体:VQFN-48 封装:Reel |
| MCP2030-I/P | 制造商:Microchip Technology Inc 功能描述:Analog Front End Device IC |
发布紧急采购，3分钟左右您将得到回复。