- 您现在的位置：买卖IC网 > Datasheet目录476 > MCP2030A-I/P (Microchip Technology)IC KEYLESS ENTRY AFE 3CH 14PDIP Datasheet资料下载
参数资料
| 型号： | MCP2030A-I/P |
| 厂商： | Microchip Technology |
| 文件页数： | 46/66页 |
| 文件大小： | 0K |
| 描述： | IC KEYLESS ENTRY AFE 3CH 14PDIP |
| 标准包装： | 30 |
| RF 型： | PEG，TPMS |
| 频率： | 125kHz |
| 特点： | 4 通道 |
| 封装/外壳： | 14-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 14-PDIP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页当前第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页
MCP2030
5.30.3.1
ANALOG-TO-DIGITAL DATA
5.31
C onfiguration Registers
CONVERSION OF RSSI SIGNAL
The RSSI output is an analog current. It needs an
5.31.1
SPI COMMUNICATION
external Analog-to-Digital (ADC) data conversion
device for digitized output. The ADC data conversion
can be accomplished by using a stand-alone external
ADC device, an external MCU that has internal ADC
features, or an external MCU that has no ADC features
but instead uses firmware. The RSSIFET is used to
discharge any external charge on the LFDATA pin in
the RSSI Output mode. The MOSFET can be turned on
or off with bit RSSIFET<8> of Configuration Register 2
(Register 5-3). When it is turned on, the internal
MOSFET provides a discharge path for the external
capacitor that is connected at the LFDATA pin. This
MOSFET option is valid only if RSSI output is selected
and not controllable by users for demodulated or carrier
clock output options.
See separate application notes for various external ADC
implementation methods for this device.
See Figure 5-8 for RSSI output path.
The SPI communication is used to read from or write to
the Configuration registers and to send command-only
messages. Three pins are used for SPI
communication: CS, SCLK/ALERT, and LFDATA/RSSI/
CCLK/SDIO. Figure 5-9, Figure 5-10 and Figure 5-11
show examples of the SPI communication sequences.
When these pins are connected to the external MCU
I/O pins, the following are needed:
CS
? Pin is permanently an input with an internal pull-up.
SCLK/ALERT
? Pin is an open collector output when CS is high.
An internal pull-up resistor exists to ensure no
spurious SPI communication between powering
and the MCU configuring its pins. This pin
becomes the SPI clock input when CS is low.
LFDATA/CCLK/SDIO
? Pin is a digital output (LFDATA) so long as CS is
high. During SPI communication, the pin is the
SPI data input (SDI) unless performing a register
Read, where it will be the SPI data output (SDO).
CS
SCLK/ALERT
ALERT
(open collector
output)
LFDATA/CCLK/SDIO
LFDATA
(output)
FIGURE 5-9:
DS21981A-page 46
Power-Up Sequence.
? 2005 Microchip Technology Inc.
相关PDF资料 |
PDF描述 |
|---|---|
| MCP2030DM-TPR | BOARD DEMO PICTAIL MCP2030 |
| MCP9502PT-095E/OT | IC TEMP SWITCH PROGR P-P SOT23-5 |
| MCP9510CT-E/CH | IC TEMP SWITCH OD 125C SOT23-6 |
| MD7IC18120NR1 | IC PWR AMP RF LDMOS TO270-16 |
| MDEV-315-HH-KF-MS | KIT MASTER DEV MS KEYFOB 315MHZ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP2030AT-I/SL | 功能描述:射频无线杂项 Keyless Entry AFE RoHS:否 制造商:Texas Instruments 工作频率:112 kHz to 205 kHz 电源电压-最大:3.6 V 电源电压-最小:3 V 电源电流:8 mA 最大功率耗散: 工作温度范围:- 40 C to + 110 C 封装 / 箱体:VQFN-48 封装:Reel |
| MCP2030AT-I/ST | 功能描述:射频无线杂项 Keyless Entry AFE RoHS:否 制造商:Texas Instruments 工作频率:112 kHz to 205 kHz 电源电压-最大:3.6 V 电源电压-最小:3 V 电源电流:8 mA 最大功率耗散: 工作温度范围:- 40 C to + 110 C 封装 / 箱体:VQFN-48 封装:Reel |
| MCP2030DM-TPR | 功能描述:射频开发工具 MCP9800 Thermal Snsr PICtail Demo Brd RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| MCP2030-I/P | 功能描述:射频无线杂项 Keyless Entry AFE RoHS:否 制造商:Texas Instruments 工作频率:112 kHz to 205 kHz 电源电压-最大:3.6 V 电源电压-最小:3 V 电源电流:8 mA 最大功率耗散: 工作温度范围:- 40 C to + 110 C 封装 / 箱体:VQFN-48 封装:Reel |
| MCP2030-I/P | 制造商:Microchip Technology Inc 功能描述:Analog Front End Device IC |
发布紧急采购，3分钟左右您将得到回复。