- 您现在的位置：买卖IC网 > Datasheet目录476 > MCP2030A-I/P (Microchip Technology)IC KEYLESS ENTRY AFE 3CH 14PDIP Datasheet资料下载
参数资料
| 型号： | MCP2030A-I/P |
| 厂商： | Microchip Technology |
| 文件页数： | 33/66页 |
| 文件大小： | 0K |
| 描述： | IC KEYLESS ENTRY AFE 3CH 14PDIP |
| 标准包装： | 30 |
| RF 型： | PEG，TPMS |
| 频率： | 125kHz |
| 特点： | 4 通道 |
| 封装/外壳： | 14-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 14-PDIP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页当前第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页
MCP2030
5.14.2
INACTIVITY TIMER
The timer is reset when the:
The Inactivity Timer is used to automatically return the
device to Standby mode, if there is no input signal. The
time-out period is approximately 16 ms (T INACT ), based
on the 32 kHz internal clock.
The purpose of the Inactivity Timer is to minimize
current draw by automatically returning to the lower
current Standby mode, if there is no input signal for
approximately 16 ms.
The timer is reset when:
? An amplitude change in LF input signal, either
high-to-low or low-to-high
? CS pin is low (any SPI command)
? CS pin is low (any SPI command).
? Output enable filter is disabled.
? LFDATA pin is enabled (signal passed output
enable filter).
The timer starts after the AGC initialization time.
The timer causes a low output on the ALERT pin when:
? Output enable filter is enabled and modulated
input signal is present for T ALARM , but does not
pass the output enable filter requirement.
Note: The Alarm timer is disabled if the output
enable filter is disabled.
? Timer-related Soft Reset
5.14.4
PULSE WIDTH TIMER
The timer starts after AGC initialization time (T AGC ).
The timer causes a Soft Reset when:
? A previously received input signal does not
change either high-to-low or low-to-high for
T INACT
The Soft Reset returns the device to Standby mode
where most of the analog circuits, such as the AGC,
demodulator and RC oscillator, are powered down. This
The Pulse Width Timer is used to verify that the
received output enable sequence meets both the
minimum T OEH and minimum T OEL requirements.
5.14.5 PERIOD TIMER
The Period Timer is used to verify that the received
output enable sequence meets the maximum T OET
requirement.
returns the device to the lower Standby Current mode.
5.14.6
AGC INITIALIZATION TIMER (T AGC )
5.14.3 ALARM TIMER
The Alarm Timer is used to notify the external MCU that
the device is receiving an input signal that does not pass
the output enable filter requirement. The time-out period
is approximately 32 ms (T ALARM ) in the presence of
continuing noise.
The Alarm Timer time-out occurs if there is an input
signal for longer than 32 ms that does not meet the
output enable filter requirements. The Alarm Timer
time-out causes:
This timer is used to keep the output enable filter in
Reset while the AGC settles on the input signal. The
time-out period is approximately 3.5 ms. At the end of
this time (T AGC ), the input should remain high (T PAGC ),
otherwise the counting is aborted and a Soft Reset is
issued. See Figure 5-4 for details.
Note 1: The device needs continuous and
uninterrupted high input signal during
AGC initialization time (T AGC ). Any
absence of signal during this time may
reset the timer and a new input signal is
a)
b)
The ALERT pin to go low.
The ALARM bit to set in the Status
needed for AGC settling time, or may
result in improper AGC gain settings
STATUS Register 7 (Register 5-8).
The external MCU is informed of the Alarm timer time-
out by monitoring the ALERT pin. If the Alarm timer
time-out occurs, the external MCU can take
appropriate actions such as lowering channel
sensitivity or disabling channels. If the noise source is
ignored, the device can return to a lower standby
current draw state.
? 2005 Microchip Technology Inc.
which will produce invalid output.
2: The rest of the device section wakes up
if any of these input channels receive
the AGC settling time correctly. STATUS
Register 7 bits <4:2> (Register 5-8) indi-
cate which input channels have waken
up the device first. Valid input signal on
multiple input pins can cause more than
one channel's indicator bit to be set.
DS21981A-page 33
相关PDF资料 |
PDF描述 |
|---|---|
| MCP2030DM-TPR | BOARD DEMO PICTAIL MCP2030 |
| MCP9502PT-095E/OT | IC TEMP SWITCH PROGR P-P SOT23-5 |
| MCP9510CT-E/CH | IC TEMP SWITCH OD 125C SOT23-6 |
| MD7IC18120NR1 | IC PWR AMP RF LDMOS TO270-16 |
| MDEV-315-HH-KF-MS | KIT MASTER DEV MS KEYFOB 315MHZ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP2030AT-I/SL | 功能描述:射频无线杂项 Keyless Entry AFE RoHS:否 制造商:Texas Instruments 工作频率:112 kHz to 205 kHz 电源电压-最大:3.6 V 电源电压-最小:3 V 电源电流:8 mA 最大功率耗散: 工作温度范围:- 40 C to + 110 C 封装 / 箱体:VQFN-48 封装:Reel |
| MCP2030AT-I/ST | 功能描述:射频无线杂项 Keyless Entry AFE RoHS:否 制造商:Texas Instruments 工作频率:112 kHz to 205 kHz 电源电压-最大:3.6 V 电源电压-最小:3 V 电源电流:8 mA 最大功率耗散: 工作温度范围:- 40 C to + 110 C 封装 / 箱体:VQFN-48 封装:Reel |
| MCP2030DM-TPR | 功能描述:射频开发工具 MCP9800 Thermal Snsr PICtail Demo Brd RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| MCP2030-I/P | 功能描述:射频无线杂项 Keyless Entry AFE RoHS:否 制造商:Texas Instruments 工作频率:112 kHz to 205 kHz 电源电压-最大:3.6 V 电源电压-最小:3 V 电源电流:8 mA 最大功率耗散: 工作温度范围:- 40 C to + 110 C 封装 / 箱体:VQFN-48 封装:Reel |
| MCP2030-I/P | 制造商:Microchip Technology Inc 功能描述:Analog Front End Device IC |
发布紧急采购，3分钟左右您将得到回复。