- 您现在的位置：买卖IC网 > Datasheet目录476 > MCP2030A-I/P (Microchip Technology)IC KEYLESS ENTRY AFE 3CH 14PDIP Datasheet资料下载
参数资料
| 型号： | MCP2030A-I/P |
| 厂商： | Microchip Technology |
| 文件页数： | 39/66页 |
| 文件大小： | 0K |
| 描述： | IC KEYLESS ENTRY AFE 3CH 14PDIP |
| 标准包装： | 30 |
| RF 型： | PEG，TPMS |
| 频率： | 125kHz |
| 特点： | 4 通道 |
| 封装/外壳： | 14-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 14-PDIP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页当前第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页
MCP2030
TABLE 5-2:
INPUT SENSITIVITY VS. MODULATED SIGNAL STRENGTH SETTING (AGCSIG <7>)
AGCSIG<7>
(Config. Register 5)
0
1
Description
Option Disabled – Detect any input signal level (demodulated data and
carrier clock).
Option Enabled – No output until AGC Status = 1 (i.e., V PEAK ≈ 20 mV PP )
(demodulated data and carrier clock).
? Provides the best signal to noise ratio.
Input
Sensitivity
(Typical)
3.0 mV PP
20 mV PP
5.17
Input Channels (Enable/Disable)
5.19
AGC Preserve
Each channel can be individually enabled or disabled
by programming bits in Configuration Register 0<3:1>
(Register 5-1).
The purpose of having an option to disable a particular
channel is to minimize current draw by powering down
as much circuitry as possible, if the channel is not
needed for operation. The exact circuits disabled when
an input is disabled are amplifiers, detector, full-wave
rectifier, data slicer, and modulation FET. However, the
RF input limiter remains active to protect the silicon
from excessive antenna input voltages.
The AGC preserve feature is used to preserve the AGC
value during the AGC initialization time (T AGC ) and
apply the value to the data slicing circuit for the follow-
ing data streams instead of using a new tracking value.
This feature is useful to demodulate the input signal
correctly when the input has random amplitude varia-
tions at a given time period. This feature is enabled
when the device receives an AGC Preserve On com-
mand and disabled if it receives an AGC Preserve Off
command. Once the AGC Preserve On command is
received, the device acquires a new AGC value during
each AGC initialization time and preserves the value
5.18
AGC Amplifier
until a Soft Reset or an AGC Preserve Off command is
issued. Therefore, it does not need to issue another
The circuit automatically amplifies input signal voltage
levels to an acceptable level for the data slicer. Fast
attack and slow release by nature, the AGC tracks the
carrier signal level and not the modulated data bits.
The AGC inherently tracks the strongest of the three
antenna input signals. The AGC requires an AGC
initialization time (T AGC ).
The AGC will attempt to regulate a channel’s peak
signal voltage into the data slicer to a desired regulated
AGC voltage – reducing the input path’s gain as the
signal level attempts to increase above regulated AGC
voltage, and allowing full amplification on signal levels
below the regulated AGC voltage.
The AGC has two modes of operation:
AGC Preserve On command. An AGC Preserve Off
command is needed to disable the AGC preserve
feature (see Section 5.31.2.5 “AGC Preserve On
Command” and Section 5.31.2.6 “AGC Preserve Off
Command” for AGC Preserve commands).
1.
2.
During the AGC initialization time (T AGC ), the
AGC time constant is fast, allowing a reasonably
short acquisition time of the continuous input
signal.
After T AGC , the AGC switches to a slower time
constant for data slicing.
Also, the AGC is frozen when the input signal envelope
is low. The AGC tracks only high envelope levels.
? 2005 Microchip Technology Inc.
DS21981A-page 39
相关PDF资料 |
PDF描述 |
|---|---|
| MCP2030DM-TPR | BOARD DEMO PICTAIL MCP2030 |
| MCP9502PT-095E/OT | IC TEMP SWITCH PROGR P-P SOT23-5 |
| MCP9510CT-E/CH | IC TEMP SWITCH OD 125C SOT23-6 |
| MD7IC18120NR1 | IC PWR AMP RF LDMOS TO270-16 |
| MDEV-315-HH-KF-MS | KIT MASTER DEV MS KEYFOB 315MHZ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP2030AT-I/SL | 功能描述:射频无线杂项 Keyless Entry AFE RoHS:否 制造商:Texas Instruments 工作频率:112 kHz to 205 kHz 电源电压-最大:3.6 V 电源电压-最小:3 V 电源电流:8 mA 最大功率耗散: 工作温度范围:- 40 C to + 110 C 封装 / 箱体:VQFN-48 封装:Reel |
| MCP2030AT-I/ST | 功能描述:射频无线杂项 Keyless Entry AFE RoHS:否 制造商:Texas Instruments 工作频率:112 kHz to 205 kHz 电源电压-最大:3.6 V 电源电压-最小:3 V 电源电流:8 mA 最大功率耗散: 工作温度范围:- 40 C to + 110 C 封装 / 箱体:VQFN-48 封装:Reel |
| MCP2030DM-TPR | 功能描述:射频开发工具 MCP9800 Thermal Snsr PICtail Demo Brd RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| MCP2030-I/P | 功能描述:射频无线杂项 Keyless Entry AFE RoHS:否 制造商:Texas Instruments 工作频率:112 kHz to 205 kHz 电源电压-最大:3.6 V 电源电压-最小:3 V 电源电流:8 mA 最大功率耗散: 工作温度范围:- 40 C to + 110 C 封装 / 箱体:VQFN-48 封装:Reel |
| MCP2030-I/P | 制造商:Microchip Technology Inc 功能描述:Analog Front End Device IC |
发布紧急采购，3分钟左右您将得到回复。