- 您现在的位置：买卖IC网 > PDF目录45388 > MSC7119VM1200 (FREESCALE SEMICONDUCTOR INC) 0-BIT, 300 MHz, OTHER DSP, PBGA400 PDF资料下载
参数资料
| 型号： | MSC7119VM1200 |
| 厂商： | FREESCALE SEMICONDUCTOR INC |
| 元件分类： | 数字信号处理 |
| 英文描述： | 0-BIT, 300 MHz, OTHER DSP, PBGA400 |
| 封装： | LEAD FREE, MAPBGA-400 |
| 文件页数： | 53/60页 |
| 文件大小： | 1138K |
| 代理商： | MSC7119VM1200 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页当前第53页第54页第55页第56页第57页第58页第59页第60页
Ordering Information
MSC7119 Data Sheet, Rev. 8
Freescale Semiconductor
57
3.6
Connectivity Guidelines
This section summarizes the connections and special conditions, such as pull-up or pull-down resistors, for the MSC7119
device. Following are guidelines for signal groups and configuration settings:
Clock and reset signals.
— SWTE is used to configure the MSC7119 device and is sampled on the deassertion of PORESET, so it should be
tied to VDDC or GND either directly or through pull-up or pull-down resistors until PORESET is deasserted. After
PORESET
, this signal can be left floating.
— BM[0–1] configure the MSC7119 device and are sampled until PORESET is deasserted, so they should be tied to
VDDIO or GND either directly or through pull-up or pull-down resistors.
— HRESET should be pulled up.
Interrupt signals. When used, IRQ pins must be pulled up.
HDI16 signals.
— When they are configured for open-drain, the HREQ/HREQ or HTRQ/HTRQ signals require a pull-up resistor.
However, these pins are also sampled at power-on reset to determine the HDI16 boot mode and may need to be
pulled down. When these pins must be pulled down on reset and pulled up otherwise, a buffer can be used with
the HRESET signal as the enable.
— When the device boots through the HDI16, the HDDS, HDSP and H8BIT pins should be pulled up or down,
depending on the required boot mode settings.
Ethernet MAC/TDM2 signals. The MDIO signal requires an external pull-up resistor.
I2C signals. The SCL and SDA signals, when programmed for I2C, requires an external pull-up resistor.
General-purpose I/O (GPIO) signals. An unused GPIO pin can be disconnected. After boot, program it as an output
pin.
Other signals.
—The TEST0 pin must be connected to ground.
—The TPSEL pin should be pulled up to enable debug access via the EOnCE port and pulled down for boundary
scan.
— Pins labelled NO CONNECT (NC) must not be connected.
— When a 16-pin double data rate (DDR) interface is used, the 16 unused data pins should be no connects (floating)
if the used lines are terminated.
— Do not connect DBREQ to DONE (as you would for the MSC8101 device). Connect DONE to one of the EVNT
pins, and DBREQ to HRRQ.
4
Ordering Information
Consult a Freescale Semiconductor sales office or authorized distributor to determine product availability and place an order.
Part
Supply Voltage
Package Type
Pin
Count
Core
Frequency
(MHz)
Solder Spheres
Order Number
MSC7119
1.2 V core
2.5 V memory
3.3 V I/O
Molded Array Process-Ball Grid
Array (MAP-BGA)
400
300
Lead-free
MSC7119VM1200
Lead-bearing
MSC7119VF1200
相关PDF资料 |
PDF描述 |
|---|---|
| MSC8102M4000 | 32-BIT, 75 MHz, OTHER DSP, CBGA431 |
| MSC8122TVT6400 | 32-BIT, 400 MHz, OTHER DSP, PBGA431 |
| MSC8122TVT4800V | 32-BIT, 300 MHz, OTHER DSP, PBGA431 |
| MSC8122MP8000 | 32-BIT, 500 MHz, OTHER DSP, PBGA431 |
| MSC8144ETVT800B | 133 MHz, OTHER DSP, PBGA783 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MSC711XADS | 功能描述:开发板和工具包 - 其他处理器 DEV SYS FOR FSL 711X DEV RoHS:否 制造商:Freescale Semiconductor 产品:Development Systems 工具用于评估:P3041 核心:e500mc 接口类型:I2C, SPI, USB 工作电源电压: |
| MSC711XEVM | 功能描述:开发板和工具包 - 其他处理器 EVAL KIT W/FULL LIC CW RoHS:否 制造商:Freescale Semiconductor 产品:Development Systems 工具用于评估:P3041 核心:e500mc 接口类型:I2C, SPI, USB 工作电源电压: |
| MSC711XEVMT | 功能描述:KIT EVAL W/FULL LIC CW RoHS:是 类别:编程器，开发系统 >> 过时/停产零件编号 系列:* 标准包装:1 系列:- 传感器类型:CMOS 成像，彩色（RGB） 传感范围:WVGA 接口:I²C 灵敏度:60 fps 电源电压:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相关产品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
| MSC7121VRF | 制造商:Freescale Semiconductor 功能描述:GPON UMC 140 MHZ - Trays |
| MSC7128 | 制造商:OKI 制造商全称:OKI electronic componets 功能描述:5 x 7-Dot Character x 16-Digit Display Controller/Driver |
发布紧急采购，3分钟左右您将得到回复。