- 您现在的位置：买卖IC网 > PDF目录385639 > MT46V64M8 (Micron Technology, Inc.) 16 Meg x 8 x 4 banks DDR SDRAM(16M x 8 x 4组,双数据速率同步动态RAM) PDF资料下载
参数资料
| 型号： | MT46V64M8 |
| 厂商： | Micron Technology, Inc. |
| 英文描述： | 16 Meg x 8 x 4 banks DDR SDRAM(16M x 8 x 4组,双数据速率同步动态RAM) |
| 中文描述： | 16梅格× 8 × 4银行DDR SDRAM内存（1,600 × 8 × 4组，双数据速率同步动态RAM）的 |
| 文件页数： | 14/70页 |
| 文件大小： | 2524K |
| 代理商： | MT46V64M8 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页
14
512Mb: x4, x8, x16 DDR SDRAM
512Mx4x8x16DDR_A.p65
–
Rev. A; Pub 10/00
Micron Technology, Inc., reserves the right to change products or specifications without notice.
2000, Micron Technology, Inc.
512Mb: x4, x8, x16
DDR SDRAM
ADVANCE
DESELECT
The DESELECT function (CS# HIGH) prevents new
commands from being executed by the DDR SDRAM.
The DDR SDRAM is effectively deselected. Operations
already in progress are not affected.
NO OPERATION (NOP)
The NO OPERATION (NOP) command is used to
instruct the selected DDR SDRAM to perform a NOP
(CS# LOW). This prevents unwanted commands from
being registered during idle or wait states. Operations
already in progress are not affected.
LOAD MODE REGISTER
The mode registers are loaded via inputs A0–A12.
See mode register descriptions in the Register Defini-
tion section. The LOAD MODE REGISTER command
can only be issued when all banks are idle, and a
subsequent executable command cannot be issued until
t
MRD is met.
A CTIV E
The ACTIVE command is used to open (or activate)
a row in a particular bank for a subsequent access. The
value on the BA0, BA1 inputs selects the bank, and the
address provided on inputs A0–A12 selects the row.
This row remains active (or open) for accesses until a
PRECHARGE command is issued to that bank.
A PRECHARGE command must be issued before open-
ing a different row in the same bank.
REA D
The READ command is used to initiate a burst read
access to an active row. The value on the BA0, BA1
inputs selects the bank, and the address provided on
inputs A0–A
i
(where
i
= 9 for x16; 9, 11 for x8; or 9, 11,
and 12 for x4) selects the starting column location. The
value on input A10 determines whether or not auto
precharge is used. If auto precharge is selected, the row
being accessed will be precharged at the end of the
READ burst; if auto precharge is not selected, the row
will remain open for subsequent accesses.
WRITE
The WRITE command is used to initiate a burst write
access to an active row. The value on the BA0, BA1
inputs selects the bank, and the address provided on
inputs A0–A
i
(where
i
= 9 for x16; 9 and 11 for x8; or 9,
11, and 12 for x4) selects the starting column location.
The value on input A10 determines whether or not auto
precharge is used. If auto precharge is selected, the row
being accessed will be precharged at the end of the
WRITE burst; if auto precharge is not selected, the row
will remain open for subsequent accesses. Input data
appearing on the DQs is written to the memory array
subject to the DM input logic level appearing coincident
with the data. If a given DM signal is registered LOW, the
corresponding data will be written to memory; if the
DM signal is registered HIGH, the corresponding data
inputs will be ignored, and a WRITE will not be executed
to that byte/column location.
PRECHA RGE
The PRECHARGE command is used to deactivate the
open row in a particular bank or the open row in all
banks. The bank(s) will be available for a subsequent row
access a specified time (
t
RP) after the PRECHARGE com-
mand is issued. Input A10 determines whether one or all
banks are to be precharged, and in the case where only
one bank is to be precharged, inputs BA0, BA1 select the
bank. Otherwise BA0, BA1 are treated as “Don’t Care.”
Once a bank has been precharged, it is in the idle state
and must be activated prior to any READ or WRITE
commands being issued to that bank. A PRECHARGE
command will be treated as a NOP if there is no open
row in that bank (idle state), or if the previously open
row is already in the process of precharging.
AUTO PRECHARGE
Auto precharge is a feature which performs the
same individual-bank precharge function described
above, but without requiring an explicit command.
This is accomplished by using A10 to enable auto
precharge in conjunction with a specific READ or
WRITE command. A precharge of the bank/row that is
addressed with the READ or WRITE command is auto-
matically performed upon completion of the READ or
WRITE burst. Auto precharge is nonpersistent in that it
is either enabled or disabled for each individual READ
or WRITE command.
Auto precharge ensures that the precharge is initi-
ated at the earliest valid stage within a burst. This
“earliest valid stage” is determined as if an explicit
PRECHARGE command was issued at the earliest pos-
sible time, without violating
t
RAS (MIN), as described
for each burst type in the Operation section of this data
sheet. The user must not issue another command to the
same bank until the precharge time (
t
RP) is completed.
BURST TERMINATE
The BURST TERMINATE command is used to trun-
cate READ bursts (with auto precharge disabled). The
most recently registered READ command prior to the
BURST TERMINATE command will be truncated, as
shown in the Operation section of this data sheet. The
open page which the READ burst was terminated from
remains open.
相关PDF资料 |
PDF描述 |
|---|---|
| MT48LC16M8A1TG | SYNCHRONOUS DRAM |
| MT48LC32M4A1 | ECONOLINE: RSZ/P - 1kVDC |
| MT48LC32M4A2 | SYNCHRONOUS DRAM |
| MT48LC32M4A1TG | SYNCHRONOUS DRAM |
| MT48LC8M16A1TG | SYNCHRONOUS DRAM |
相关代理商/技术参数 |
参数描述 |
|---|
发布紧急采购，3分钟左右您将得到回复。