参数资料
| 型号： | NCN6000DTBR2G |
| 厂商： | ON Semiconductor |
| 文件页数： | 25/36页 |
| 文件大小： | 0K |
| 描述： | IC INTERFACE SMART CARD 20TSSOP |
| 产品变化通告： | Product Obsolescence 01/Jul/2009 |
| 标准包装： | 1 |
| 应用： | ATM 终端，气泵，ISM |
| 接口： | 微控制器 |
| 电源电压： | 2.7 V ~ 6 V |
| 封装/外壳： | 20-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 20-TSSOP |
| 包装： | 剪切带 (CT) |
| 安装类型： | 表面贴装 |
| 其它名称： | NCN6000DTBR2GOSCT |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
NCN6000
http://onsemi.com
31
Security Features
In order to protect both the interface and the external smart
card, the NCN6000 provides security features to prevent
catastrophic failures as depicted here after.
Pin Current Limitation: In the case of a short circuit to
ground, the current forced by the device is limited to 15 mA
for any pins, except CRD_CLK pin. No feedback is
provided to the external MPU.
DCDC Operation: The internal circuit continuously
senses the CRD_VCC voltage and, in the case of either over
or undervoltage situation, update the STATUS register
accordingly. This register can be read out by the MPU.
Battery Voltage: Both the Over and Undervoltage are
detected by the NCN6000, a POWER_DOWN sequence
and the STATUS register being updated accordingly. The
external MPU can read the STATUS pin to take whatever is
appropriate to cope with the situation.
ESD Protection
The NCN6000 includes silicon devices to protect the pins
against the ESD spikes voltages. To cope with the different
ESD voltages developed across these pins, the builtin
structures have been designed to handle either 2.0 kV, when
related to the microcontroller side, or 8.0 kV when
connected with the external contacts. Practically, the
CRD_RST, CRD_CLK, CRD_IO and CRD_DET pins can
sustain 8 kV, the digital pins being capable to sustain 2 kV.
The CRD_VCC pin has the same 8 kV ESD protection, but
can source up to 55 mA continuously, the absolute
maximum current being 100 mA.
To save as much battery current as possible when no card
is inserted, one should use a Normally Open Card Detection
switch connected pin 11. Since the internal card detection
circuit source 10
mA (typical) to bias the switch, using a
Normally Open avoid this direct sink to ground from the
battery.
Parallel Operation
When two or more NCN6000 operate in parallel on a
common digital bus, the Chip Select pin allows the selection
of one chip from the bank of the paralleled devices. Of
course, the external MPU shall provide one unique CS line
for each of the NCN6000 considered interfaces. When a
given interface is selected by CS = L, all the logic inputs
becomes active, the chip can be programmed or/and the
external card can be accessed. When CS = H, all the input
logic pins are in the high impedance state, thus leaving the
bus available for other purpose. On the other hand, when
CS = H, the CRD_IO and CRD_RST hold the previous I/O
and RESET logic state, the CRD_CLK being either active
or stopped, according to the programmed state forced by the
MPU.
Since there is one single I/O line to communicate with the
external microcontroller, one should provide a software
routine to save the code when data exchanged are performed
between the two cards. Generally speaking, the internal
microcontroller RAM can be used to support such a
transaction.
The CRD_VCC voltage and CRD_CLK signal of each
NCN6000 can be operated simultaneously, these two pins
being activated even when the related chip select is High. As
depicted in Figure 14, the DCDC converter is not
deactivated when PWR_ON goes to Low when CS = High.
Minimum Power Consumption
To achieve a minimum current consumption, the interface
shall be programmed as follow:
1. Turn off the DCDC converter : this will
disconnect the smart card if still inserted in the
socket), reducing the power supply to the
minimum needed to control the interface.
2. Force the input signals to a logic High to avoid
current flowing through the pull up resistors. This
applies to the here below table:
INT
Pin 9
CS
Pin 6
STATUS
Pin 5
I/O
Pin 8
CRD_IO
Pin 14
To save as much battery current as possible when no card
is inserted, one should use a Normally Open Card Detection
switch connected pin 11 to ground. Since the internal card
detection circuit source is 10
mA (typical), using such a NO
switch saves the direct sink to ground current from the
battery to ground.
During this mode of operation, the only active sub
functions are the card detection and the battery monitoring.
The activity resume immediately after either a card
insertion, or a CS = Low signal applied to pin 6.
相关PDF资料 |
PDF描述 |
|---|---|
| NCN6001DTBR2 | IC INTERFACE SMART CARD 20TSSOP |
| NCN6004AFTBR2G | IC INTERFACE SAM/SIM DUAL 48TQFP |
| NCN6804MNR2G | IC SMART CARD DUAL W/SPI 32-QFN |
| NCN7200MTTWG | IC MUX/DEMUX OCTAL 1X2 42WQFN |
| NCN8024DTBR2G | SMART CARD IC 5V/3V TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCN6001 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Smartcard Interface ICs |
| NCN6001/D | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Compact Smart Card Interface IC |
| NCN6001_06 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Compact Smart Card Interface IC |
| NCN6001_0610 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Smartcard Interface ICs |
| NCN6001DTBEVB | 功能描述:界面开发工具 NCN6001 TSSOP EVAL BOARD RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
发布紧急采购，3分钟左右您将得到回复。