参数资料
| 型号： | NCN6000DTBR2G |
| 厂商： | ON Semiconductor |
| 文件页数： | 7/36页 |
| 文件大小： | 0K |
| 描述： | IC INTERFACE SMART CARD 20TSSOP |
| 产品变化通告： | Product Obsolescence 01/Jul/2009 |
| 标准包装： | 1 |
| 应用： | ATM 终端，气泵，ISM |
| 接口： | 微控制器 |
| 电源电压： | 2.7 V ~ 6 V |
| 封装/外壳： | 20-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 20-TSSOP |
| 包装： | 剪切带 (CT) |
| 安装类型： | 表面贴装 |
| 其它名称： | NCN6000DTBR2GOSCT |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
NCN6000
http://onsemi.com
15
Basic Operating Modes Flow Chart
The NCN6000 brings all the functions necessary to handle
data communication between a host computer and the smart
card. The builtin Chip Select pin provides a simple way to
share the same MPU bus with several card interface. On top
of that, the logic control are derived from specific pins,
avoiding the risk of mixing up the operation when the
interface is controlled by a low end microcontroller.
During the transaction operation, the external MPU takes
care of whatever is necessary to he data on the single
bidirectional I/O line. Leaving aside the DCDC control and
associated failures, the NCN6000 does not take any further
responsibility in the data transaction.
When the chip operates in the programming mode, the
NCN6000 provide a flexible access to set up the CRD_VCC
voltage, the CRD_CLK and the CRD_DET smart card
signals.
The external microcontroller takes care of the smart card
transaction and shall handle the interface accordingly.
Figure 7. Operating Modes Flow Chart
RESET
Vbat = OK
STAND BY MODE
SELECT OPERATING MODE
PROGRAMMING
MODE
SET NCN6000
PARAMETERS
ACTIVE MODE
SEND ATR SEQUENCE
TRANSACTION MODE
END MODE
POWER DOWN SEQUENCE
IDLE MODE
FINISH
PWR_ON = H
CS = H
PGM = H
PGM = L
CS = L
PGM = H
CS = L
LATCH NCN6000
PARAMETERS
PGM = H
CS = H
Standby Mode
The Standby Mode allows the NCN6000 to detect a card
insertion, keeping the power consumption at a minimum.
The power supply CRD_VCC is not applied to the card, until
the external controllers set PWR_ON = H with CS = L.
Standby Mode
Logic Conditions:
Card Output:
CS
= H
PWR_ON = H
A0
= Z
A1
= Z
PGM
= Z
I/O
= Z
RESET
= Z
CRD_VCC = 0 V
CRD_CLK = L
CRD_RST = L
CRD_IO
= L
When a card is inserted, the internal logic filters the signal
present pin 11, then asserts the INT pin to Low if the pulse
applied to CRD_DET is longer than 150
ms. The external
MPU shall run whatever is necessary to handle the card.
The INT is cleared (return to High) when a positive going
transition is asserted to either the CS or to the PWR_ON
signal logically combined with Chip Select = Low.
相关PDF资料 |
PDF描述 |
|---|---|
| NCN6001DTBR2 | IC INTERFACE SMART CARD 20TSSOP |
| NCN6004AFTBR2G | IC INTERFACE SAM/SIM DUAL 48TQFP |
| NCN6804MNR2G | IC SMART CARD DUAL W/SPI 32-QFN |
| NCN7200MTTWG | IC MUX/DEMUX OCTAL 1X2 42WQFN |
| NCN8024DTBR2G | SMART CARD IC 5V/3V TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NCN6001 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Smartcard Interface ICs |
| NCN6001/D | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Compact Smart Card Interface IC |
| NCN6001_06 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Compact Smart Card Interface IC |
| NCN6001_0610 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Smartcard Interface ICs |
| NCN6001DTBEVB | 功能描述:界面开发工具 NCN6001 TSSOP EVAL BOARD RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
发布紧急采购，3分钟左右您将得到回复。