- 您现在的位置：买卖IC网 > PDF目录1959 > P89LPC954FBD44,151 (NXP Semiconductors)IC 80C51 MCU FLASH 16K 44LQFP PDF资料下载
参数资料
| 型号： | P89LPC954FBD44,151 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 17/69页 |
| 文件大小： | 0K |
| 描述： | IC 80C51 MCU FLASH 16K 44LQFP |
| 标准包装： | 160 |
| 系列： | LPC900 |
| 核心处理器： | 8051 |
| 芯体尺寸： | 8-位 |
| 速度： | 18MHz |
| 连通性： | I²C，SPI，UART/USART |
| 外围设备： | 欠压检测/复位，POR，PWM，WDT |
| 输入/输出数： | 40 |
| 程序存储器容量： | 16KB（16K x 8） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 512 x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2.4 V ~ 3.6 V |
| 数据转换器： | A/D 8x10b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 44-LQFP |
| 包装： | 托盘 |
| 配用： | 568-1759-ND - EMULATOR DEBUGGER/PROGRMMR LPC9X |
| 其它名称： | 568-7917 568-7917-ND 568-8269 935284303151 P89LPC954FBD44,151-ND P89LPC954FBD44-S P89LPC954FBD44-S-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页
P89LPC952_954_4
NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 04 — 24 July 2008
24 of 69
NXP Semiconductors
P89LPC952/954
8-bit microcontroller with 10-bit ADC
in reset when VDD falls below the minimum specied operating voltage. These
requirements for clock frequencies above 12 MHz do not apply when using the
internal RC oscillator in clock doubler mode.
7.3.6 Clock output
The P89LPC952/954 supports a user-selectable clock output function on the
XTAL2/CLKOUT pin when crystal oscillator is not being used. This condition occurs if
another clock source has been selected (on-chip RC oscillator, watchdog oscillator,
external clock input on XTAL1) and if the RTC is not using the crystal oscillator as its clock
source. This allows external devices to synchronize to the P89LPC952/954. This output is
enabled by the ENCLK bit in the TRIM register.
The frequency of this clock output is 1
2 that of the CCLK. If the clock output is not needed
in Idle mode, it may be turned off prior to entering Idle, saving additional power.
7.4 On-chip RC oscillator option
The P89LPC952/954 has a 6-bit TRIM register that can be used to tune the frequency of
the RC oscillator. During reset, the TRIM value is initialized to a factory pre-programmed
value to adjust the oscillator frequency to 7.373 MHz
± 1 % at room temperature.
End-user applications can write to the TRIM register to adjust the on-chip RC oscillator to
other frequencies. When the clock doubler option is enabled (UCFG1.3 = 1), the output
frequency is 14.746 MHz. If CCLK is 8 MHz or slower, the CLKLP SFR bit (AUXR1.7) can
be set to logic 1 to reduce power consumption. On reset, CLKLP is logic 0 allowing
highest performance access. This bit can then be set in software if CCLK is running at
8 MHz or slower.
The requirements in Section 7.3.5 “High speed oscillator option” for conguring P1.5 as
an external reset input and using an external reset circuit when the clock frequency is
greater than 12 MHz do not apply when using the internal RC oscillator’s clock doubler
option.
7.5 Watchdog oscillator option
The watchdog has a separate oscillator which has a frequency of 400 kHz. This oscillator
can be used to save power when a high clock frequency is not needed.
7.6 External clock input option
In this conguration, the processor clock is derived from an external source driving the
P3.1/XTAL1 pin. The rate may be from 0 Hz up to 18 MHz. The P3.0/XTAL2 pin may be
used as a standard port pin or a clock output.
When using an external clock input frequency above 12 MHz, the reset input
function of P1.5 must be enabled. An external circuit is required to hold the device
in reset at power-up until VDD has reached its specied level. When system power is
removed VDD will fall below the minimum specied operating voltage. When using
an external clock input frequency above 12 MHz, in some applications, an external
brownout detect circuit may be required to hold the device in reset when VDD falls
below the minimum specied operating voltage. These requirements for clock
frequencies above 12 MHz do not apply when using the internal RC oscillator in
clock doubler mode.
相关PDF资料 |
PDF描述 |
|---|---|
| P89LPC972FN,129 | MCU 80C51 8KB FLASH 20DIP |
| P89LPC985FDH,529 | IC 80C51 MCU KB FLASH 28TSSOP |
| P89V51RC2FA,512 | IC 80C51 MCU FLASH 32K 44-PLCC |
| P89V52X2FN,112 | IC 80C51 MCU FLASH 8K 40-DIP |
| P89V662FA,512 | IC 80C51 MCU FLASH 32K 44-PLCC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| P89LPC954FBD44-S | 功能描述:8位微控制器 -MCU 16K FL/1K RAM/512B EE/10B ADC RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| P89LPC954FBD48 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core 8 kB/16 kB 3 V byte-erasable flash with 10-bit ADC |
| P89LPC954FBD48,151 | 功能描述:8位微控制器 -MCU 8B MCU 2-CLOCK 80C51 8/16KB 3V 10B RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| P89LPC970 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core 2 kB/4 kB/8 kB wide-voltage byte-erasable flash |
| P89LPC970FDH | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core 2 kB/4 kB/8 kB wide-voltage byte-erasable flash |
发布紧急采购，3分钟左右您将得到回复。