- 您现在的位置：买卖IC网 > PDF目录1959 > P89LPC954FBD44,151 (NXP Semiconductors)IC 80C51 MCU FLASH 16K 44LQFP PDF资料下载
参数资料
| 型号： | P89LPC954FBD44,151 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 44/69页 |
| 文件大小： | 0K |
| 描述： | IC 80C51 MCU FLASH 16K 44LQFP |
| 标准包装： | 160 |
| 系列： | LPC900 |
| 核心处理器： | 8051 |
| 芯体尺寸： | 8-位 |
| 速度： | 18MHz |
| 连通性： | I²C，SPI，UART/USART |
| 外围设备： | 欠压检测/复位，POR，PWM，WDT |
| 输入/输出数： | 40 |
| 程序存储器容量： | 16KB（16K x 8） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 512 x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2.4 V ~ 3.6 V |
| 数据转换器： | A/D 8x10b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 44-LQFP |
| 包装： | 托盘 |
| 配用： | 568-1759-ND - EMULATOR DEBUGGER/PROGRMMR LPC9X |
| 其它名称： | 568-7917 568-7917-ND 568-8269 935284303151 P89LPC954FBD44,151-ND P89LPC954FBD44-S P89LPC954FBD44-S-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页当前第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页
P89LPC952_954_4
NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 04 — 24 July 2008
49 of 69
NXP Semiconductors
P89LPC952/954
8-bit microcontroller with 10-bit ADC
8.4.6 Single step mode
This special mode allows ‘single-stepping’ in an auto scan conversion mode. Any
combination of the eight input channels can be selected for conversion. After each
channel is converted, an interrupt is generated, if enabled, and the ADC waits for the next
start condition. May be used with any of the start modes.
8.5 Conversion start modes
8.5.1 Timer triggered start
An A/D conversion is started by the overow of Timer 0. Once a conversion has started,
additional Timer 0 triggers are ignored until the conversion has completed. The Timer
triggered start mode is available in all ADC operating modes.
8.5.2 Start immediately
Programming this mode immediately starts a conversion. This start mode is available in all
ADC operating modes.
8.5.3 Edge triggered
An A/D conversion is started by rising or falling edge of P1.4. Once a conversion has
started, additional edge triggers are ignored until the conversion has completed. The edge
triggered start mode is available in all ADC operating modes.
8.6 Boundary limits interrupt
The ADC has both a high and low boundary limit register. The user may select whether an
interrupt is generated when the conversion result is within (or equal to) the high and low
boundary limits or when the conversion result is outside the boundary limits. An interrupt
will be generated, if enabled, if the result meets the selected interrupt criteria. The
boundary limit may be disabled by clearing the boundary limit interrupt enable.
An early detection mechanism exists when the interrupt criteria has been selected to be
outside the boundary limits. In this case, after the four MSBs have been converted, these
four bits are compared with the four MSBs of the boundary high and low registers. If the
four MSBs of the conversion meet the interrupt criteria (i.e., outside the boundary limits)
an interrupt will be generated, if enabled. If the four MSBs do not meet the interrupt
criteria, the boundary limits will again be compared after all 8 MSBs have been converted.
A boundary status register (BNDSTA0) ags the channels which caused a boundary
interrupt.
8.7 Clock divider
The ADC requires that its internal clock source be in the range of 320 kHz to 9 MHz to
maintain accuracy. A programmable clock divider that divides the clock from 1 to 8 is
provided for this purpose.
8.8 Power-down and Idle mode
In Idle mode the ADC, if enabled, will continue to function and can cause the device to exit
Idle mode when the conversion is completed if the A/D interrupt is enabled. In
Power-down mode or Total Power-down mode, the ADC does not function. If the ADC is
enabled, it will consume power. Power can be reduced by disabling the ADC.
相关PDF资料 |
PDF描述 |
|---|---|
| P89LPC972FN,129 | MCU 80C51 8KB FLASH 20DIP |
| P89LPC985FDH,529 | IC 80C51 MCU KB FLASH 28TSSOP |
| P89V51RC2FA,512 | IC 80C51 MCU FLASH 32K 44-PLCC |
| P89V52X2FN,112 | IC 80C51 MCU FLASH 8K 40-DIP |
| P89V662FA,512 | IC 80C51 MCU FLASH 32K 44-PLCC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| P89LPC954FBD44-S | 功能描述:8位微控制器 -MCU 16K FL/1K RAM/512B EE/10B ADC RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| P89LPC954FBD48 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core 8 kB/16 kB 3 V byte-erasable flash with 10-bit ADC |
| P89LPC954FBD48,151 | 功能描述:8位微控制器 -MCU 8B MCU 2-CLOCK 80C51 8/16KB 3V 10B RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| P89LPC970 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core 2 kB/4 kB/8 kB wide-voltage byte-erasable flash |
| P89LPC970FDH | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core 2 kB/4 kB/8 kB wide-voltage byte-erasable flash |
发布紧急采购，3分钟左右您将得到回复。