- 您现在的位置：买卖IC网 > PDF目录1959 > P89LPC954FBD44,151 (NXP Semiconductors)IC 80C51 MCU FLASH 16K 44LQFP PDF资料下载
参数资料
| 型号： | P89LPC954FBD44,151 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 25/69页 |
| 文件大小： | 0K |
| 描述： | IC 80C51 MCU FLASH 16K 44LQFP |
| 标准包装： | 160 |
| 系列： | LPC900 |
| 核心处理器： | 8051 |
| 芯体尺寸： | 8-位 |
| 速度： | 18MHz |
| 连通性： | I²C，SPI，UART/USART |
| 外围设备： | 欠压检测/复位，POR，PWM，WDT |
| 输入/输出数： | 40 |
| 程序存储器容量： | 16KB（16K x 8） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 512 x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2.4 V ~ 3.6 V |
| 数据转换器： | A/D 8x10b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 44-LQFP |
| 包装： | 托盘 |
| 配用： | 568-1759-ND - EMULATOR DEBUGGER/PROGRMMR LPC9X |
| 其它名称： | 568-7917 568-7917-ND 568-8269 935284303151 P89LPC954FBD44,151-ND P89LPC954FBD44-S P89LPC954FBD44-S-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页
P89LPC952_954_4
NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 04 — 24 July 2008
31 of 69
NXP Semiconductors
P89LPC952/954
8-bit microcontroller with 10-bit ADC
Brownout detection may be enabled or disabled in software.
If brownout detection is enabled the brownout condition occurs when VDD falls below the
rises above Vbo. If the P89LPC952/954 device is to operate with a power supply that can
be below 2.7 V, BOE should be left in the unprogrammed state so that the device can
operate at 2.4 V, otherwise continuous brownout reset may prevent the device from
operating.
For correct activation of brownout detect, the VDD rise and fall times must be observed.
Please see Table 11 “Static characteristics” for specications.
7.14.2 Power-on detection
The Power-on detect has a function similar to the brownout detect, but is designed to work
as power comes up initially, before the power supply voltage reaches a level where
brownout detect can work. The POF ag in the RSTSRC register is set to indicate an
initial power-up condition. The POF ag will remain set until cleared by software.
7.15 Power reduction modes
The P89LPC952/954 supports three different power reduction modes. These modes are
Idle mode, Power-down mode, and total Power-down mode.
7.15.1 Idle mode
Idle mode leaves peripherals running in order to allow them to activate the processor
when an interrupt is generated. Any enabled interrupt source or reset may terminate Idle
mode.
7.15.2 Power-down mode
The Power-down mode stops the oscillator in order to minimize power consumption. The
P89LPC952/954 exits Power-down mode via any reset, or certain interrupts. In
Power-down mode, the power supply voltage may be reduced to the data retention supply
voltage VDDR. This retains the RAM contents at the point where Power-down mode was
entered. SFR contents are not guaranteed after VDD has been lowered to VDDR, therefore
it is highly recommended to wake-up the processor via reset in this case. VDD must be
raised to within the operating range before the Power-down mode is exited.
Some chip functions continue to operate and draw power during Power-down mode,
increasing the total power used during power-down. These include: Brownout detect,
watchdog timer, comparators (note that comparators can be powered down separately),
and RTC/system timer. The internal RC oscillator is disabled unless both the RC oscillator
has been selected as the system clock and the RTC is enabled.
7.15.3 Total Power-down mode
This is the same as Power-down mode except that the brownout detection circuitry and
the voltage comparators are also disabled to conserve additional power. The internal RC
oscillator is disabled unless both the RC oscillator has been selected as the system clock
and the RTC is enabled. If the internal RC oscillator is used to clock the RTC during
power-down, there will be high power consumption. Please use an external low frequency
clock to achieve low power with the RTC running during power-down.
相关PDF资料 |
PDF描述 |
|---|---|
| P89LPC972FN,129 | MCU 80C51 8KB FLASH 20DIP |
| P89LPC985FDH,529 | IC 80C51 MCU KB FLASH 28TSSOP |
| P89V51RC2FA,512 | IC 80C51 MCU FLASH 32K 44-PLCC |
| P89V52X2FN,112 | IC 80C51 MCU FLASH 8K 40-DIP |
| P89V662FA,512 | IC 80C51 MCU FLASH 32K 44-PLCC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| P89LPC954FBD44-S | 功能描述:8位微控制器 -MCU 16K FL/1K RAM/512B EE/10B ADC RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| P89LPC954FBD48 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core 8 kB/16 kB 3 V byte-erasable flash with 10-bit ADC |
| P89LPC954FBD48,151 | 功能描述:8位微控制器 -MCU 8B MCU 2-CLOCK 80C51 8/16KB 3V 10B RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| P89LPC970 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core 2 kB/4 kB/8 kB wide-voltage byte-erasable flash |
| P89LPC970FDH | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core 2 kB/4 kB/8 kB wide-voltage byte-erasable flash |
发布紧急采购，3分钟左右您将得到回复。