参数资料
型号: P89LPC954FBD44,151
厂商: NXP Semiconductors
文件页数: 20/69页
文件大小: 0K
描述: IC 80C51 MCU FLASH 16K 44LQFP
标准包装: 160
系列: LPC900
核心处理器: 8051
芯体尺寸: 8-位
速度: 18MHz
连通性: I²C,SPI,UART/USART
外围设备: 欠压检测/复位,POR,PWM,WDT
输入/输出数: 40
程序存储器容量: 16KB(16K x 8)
程序存储器类型: 闪存
RAM 容量: 512 x 8
电压 - 电源 (Vcc/Vdd): 2.4 V ~ 3.6 V
数据转换器: A/D 8x10b
振荡器型: 内部
工作温度: -40°C ~ 85°C
封装/外壳: 44-LQFP
包装: 托盘
配用: 568-1759-ND - EMULATOR DEBUGGER/PROGRMMR LPC9X
其它名称: 568-7917
568-7917-ND
568-8269
935284303151
P89LPC954FBD44,151-ND
P89LPC954FBD44-S
P89LPC954FBD44-S-ND
P89LPC952_954_4
NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 04 — 24 July 2008
27 of 69
NXP Semiconductors
P89LPC952/954
8-bit microcontroller with 10-bit ADC
Each interrupt source can be individually programmed to one of four priority levels by
setting or clearing bits in the interrupt priority registers IP0, IP0H, IP1, IP1H, IP2, and
IP2H. An interrupt service routine in progress can be interrupted by a higher priority
interrupt, but not by another interrupt of the same or lower priority. The highest priority
interrupt service cannot be interrupted by any other interrupt source. If two requests of
different priority levels are pending at the start of an instruction, the request of higher
priority level is serviced.
If requests of the same priority level are pending at the start of an instruction, an internal
polling sequence determines which request is serviced. This is called the arbitration
ranking. Note that the arbitration ranking is only used to resolve pending requests of the
same priority level.
7.12.1 External interrupt inputs
The P89LPC952/954 has two external interrupt inputs as well as the Keypad Interrupt
function. The two interrupt inputs are identical to those present on the standard 80C51
microcontrollers.
These external interrupts can be programmed to be level-triggered or edge-triggered by
setting or clearing bit IT1 or IT0 in Register TCON.
In edge-triggered mode, if successive samples of the INTn pin show a HIGH in one cycle
and a LOW in the next cycle, the interrupt request ag IEn in TCON is set, causing an
interrupt request.
If an external interrupt is enabled when the P89LPC952/954 is put into Power-down or Idle
mode, the interrupt will cause the processor to wake-up and resume operation. Refer to
相关PDF资料
PDF描述
P89LPC972FN,129 MCU 80C51 8KB FLASH 20DIP
P89LPC985FDH,529 IC 80C51 MCU KB FLASH 28TSSOP
P89V51RC2FA,512 IC 80C51 MCU FLASH 32K 44-PLCC
P89V52X2FN,112 IC 80C51 MCU FLASH 8K 40-DIP
P89V662FA,512 IC 80C51 MCU FLASH 32K 44-PLCC
相关代理商/技术参数
参数描述
P89LPC954FBD44-S 功能描述:8位微控制器 -MCU 16K FL/1K RAM/512B EE/10B ADC RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
P89LPC954FBD48 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core 8 kB/16 kB 3 V byte-erasable flash with 10-bit ADC
P89LPC954FBD48,151 功能描述:8位微控制器 -MCU 8B MCU 2-CLOCK 80C51 8/16KB 3V 10B RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
P89LPC970 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core 2 kB/4 kB/8 kB wide-voltage byte-erasable flash
P89LPC970FDH 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core 2 kB/4 kB/8 kB wide-voltage byte-erasable flash