- 您现在的位置：买卖IC网 > PDF目录271228 > S71PL254JC0BAITU3 (SPANSION LLC) SPECIALTY MEMORY CIRCUIT, PBGA84 PDF资料下载
参数资料
| 型号： | S71PL254JC0BAITU3 |
| 厂商： | SPANSION LLC |
| 元件分类： | 存储器 |
| 英文描述： | SPECIALTY MEMORY CIRCUIT, PBGA84 |
| 封装： | 8 X 11.60 MM, 1.40 MM HEIGHT, FBGA-84 |
| 文件页数： | 151/188页 |
| 文件大小： | 5078K |
| 代理商： | S71PL254JC0BAITU3 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页当前第151页第152页第153页第154页第155页第156页第157页第158页第159页第160页第161页第162页第163页第164页第165页第166页第167页第168页第169页第170页第171页第172页第173页第174页第175页第176页第177页第178页第179页第180页第181页第182页第183页第184页第185页第186页第187页第188页
64
S29PL127J/S29PL064J/S29PL032J for MCP
S29PL127_064_032J_00_A1 May 21, 2004
Prelimin ary
operation. The program command sequence should be reinitiated once that bank
has returned to the read mode, to ensure data integrity. Note that the SecSi Sec-
tor, autoselect and CFI functions are unavailable when the SecSi Sector is
enabled.
Programming is allowed in any sequence and across sector boundaries. A bit
cannot be programmed from “0” back to a “1.” Attempting to do so may
cause that bank to set DQ5 = 1, or cause the DQ7 and DQ6 status bits to indicate
the operation was successful. However, a succeeding read will show that the data
is still “0.” Only erase operations can convert a “0” to a “1.”
Unlock Bypass Command Sequence
The unlock bypass feature allows the system to program data to a bank faster
than using the standard program command sequence. The unlock bypass com-
mand sequence is initiated by first writing two unlock cycles. This is followed by
a third write cycle containing the unlock bypass command, 20h. That bank then
enters the unlock bypass mode. A two-cycle unlock bypass program command
sequence is all that is required to program in this mode. The first cycle in this se-
quence contains the unlock bypass program command, A0h; the second cycle
contains the program address and data. Additional data is programmed in the
same manner. This mode dispenses with the initial two unlock cycles required in
the standard program command sequence, resulting in faster total programming
time. Table 17 shows the requirements for the command sequence.
During the unlock bypass mode, only the Unlock Bypass Program and Unlock By-
pass Reset commands are valid. To exit the unlock bypass mode, the system
must issue the two-cycle unlock bypass reset command sequence. (See Table 18)
The device offers accelerated program operations through the WP#/ACC pin.
When the system asserts VHH on the WP#/ACC pin, the device automatically en-
ters the Unlock Bypass mode. The system may then write the two-cycle Unlock
Bypass program command sequence. The device uses the higher voltage on the
WP#/ACC pin to accelerate the operation. Note that the WP#/ACC pin must not
be at VHH any operation other than accelerated programming, or device damage
may result. In addition, the WP#/ACC pin must not be left floating or uncon-
nected; inconsistent behavior of the device may result.
4 illustrates the algorithm for the program operation. Refer to the Erase/Program
Operations table in the AC Characteristics section for parameters, and Figure 14
for timing diagrams.
相关PDF资料 |
PDF描述 |
|---|---|
| S71PL032JF0BFW074 | SPECIALTY MEMORY CIRCUIT, PBGA56 |
| S29AL016D90MFN011 | 1M X 16 FLASH 3V PROM, 90 ns, PDSO44 |
| SM-5MIN-A-TL-26 | RF COAXIAL RELAY, SP5T, FAILSAFE, 2875mW (COIL), 26500MHz, PANEL MOUNT |
| SM-5MIN-A-TL | RF COAXIAL RELAY, SP5T, FAILSAFE, 2875mW (COIL), 18000MHz, PANEL MOUNT |
| SM-5MIN-A | RF COAXIAL RELAY, SP5T, FAILSAFE, 2875mW (COIL), 18000MHz, PANEL MOUNT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| S71PL254JC0BAW0Z0 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:Based MCPs |
| S71PL254JC0BAW0Z2 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:Based MCPs |
| S71PL254JC0BAW0Z3 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:Based MCPs |
| S71PL254JC0BAW9Z0 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:Based MCPs |
| S71PL254JC0BAW9Z2 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:Based MCPs |
发布紧急采购，3分钟左右您将得到回复。