- 您现在的位置：买卖IC网 > PDF目录271228 > S71PL254JC0BAITU3 (SPANSION LLC) SPECIALTY MEMORY CIRCUIT, PBGA84 PDF资料下载
参数资料
| 型号： | S71PL254JC0BAITU3 |
| 厂商： | SPANSION LLC |
| 元件分类： | 存储器 |
| 英文描述： | SPECIALTY MEMORY CIRCUIT, PBGA84 |
| 封装： | 8 X 11.60 MM, 1.40 MM HEIGHT, FBGA-84 |
| 文件页数： | 165/188页 |
| 文件大小： | 5078K |
| 代理商： | S71PL254JC0BAITU3 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页第160页第161页第162页第163页第164页当前第165页第166页第167页第168页第169页第170页第171页第172页第173页第174页第175页第176页第177页第178页第179页第180页第181页第182页第183页第184页第185页第186页第187页第188页
May 21, 2004 S29PL127_064_032J_00_A1
S29PL127J/S29PL064J/S29PL032J for MCP
77
Prelimin ary
store the value of the toggle bit after the first read. After the second read, the
system would compare the new value of the toggle bit with the first. If the toggle
bit is not toggling, the device has completed the program or erase operation. The
system can read array data on DQ7–DQ0 on the following read cycle.
However, if after the initial two read cycles, the system determines that the toggle
bit is still toggling, the system also should note whether the value of DQ5 is high
(see the section on DQ5). If it is, the system should then determine again
whether the toggle bit is toggling, since the toggle bit may have stopped toggling
just as DQ5 went high. If the toggle bit is no longer toggling, the device has suc-
cessfully completed the program or erase operation. If it is still toggling, the
device did not completed the operation successfully, and the system must write
the reset command to return to reading array data.
The remaining scenario is that the system initially determines that the toggle bit
is toggling and DQ5 has not gone high. The system may continue to monitor the
toggle bit and DQ5 through successive read cycles, determining the status as de-
scribed in the previous paragraph. Alternatively, it may choose to perform other
system tasks. In this case, the system must start at the beginning of the algo-
rithm when it returns to determine the status of the operation (top of Figure 7).
DQ5: Exceeded Timing Limits
DQ5 indicates whether the program or erase time has exceeded a specified inter-
nal pulse count limit. Under these conditions DQ5 produces a “1,” indicating that the
program or erase cycle was not successfully completed.
The device may output a “1” on DQ5 if the system tries to program a “1” to a
location that was previously programmed to “0.” Only an erase operation can
change a “0” back to a “1.” Under this condition, the device halts the opera-
tion, and when the timing limit has been exceeded, DQ5 produces a “1.”
Under both these conditions, the system must write the reset command to return
to the read mode (or to the erase-suspend-read mode if a bank was previously
in the erase-suspend-program mode).
DQ3: Sector Erase Timer
After writing a sector erase command sequence, the system may read DQ3 to de-
termine whether or not erasure has begun. (The sector erase timer does not
apply to the chip erase command.) If additional sectors are selected for erasure,
the entire time-out also applies after each additional sector erase command.
When the time-out period is complete, DQ3 switches from a “0” to a “1.” See also
After the sector erase command is written, the system should read the status of
DQ7 (Data# Polling) or DQ6 (Toggle Bit I) to ensure that the device has accepted
the command sequence, and then read DQ3. If DQ3 is “1,” the Embedded Erase
algorithm has begun; all further commands (except Erase Suspend) are ignored
until the erase operation is complete. If DQ3 is “0,” the device will accept addi-
tional sector erase commands. To ensure the command has been accepted, the
system software should check the status of DQ3 prior to and following each sub-
sequent sector erase command. If DQ3 is high on the second status check, the
last command might not have been accepted.
Table 19 shows the status of DQ3 relative to the other status bits.
相关PDF资料 |
PDF描述 |
|---|---|
| S71PL032JF0BFW074 | SPECIALTY MEMORY CIRCUIT, PBGA56 |
| S29AL016D90MFN011 | 1M X 16 FLASH 3V PROM, 90 ns, PDSO44 |
| SM-5MIN-A-TL-26 | RF COAXIAL RELAY, SP5T, FAILSAFE, 2875mW (COIL), 26500MHz, PANEL MOUNT |
| SM-5MIN-A-TL | RF COAXIAL RELAY, SP5T, FAILSAFE, 2875mW (COIL), 18000MHz, PANEL MOUNT |
| SM-5MIN-A | RF COAXIAL RELAY, SP5T, FAILSAFE, 2875mW (COIL), 18000MHz, PANEL MOUNT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| S71PL254JC0BAW0Z0 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:Based MCPs |
| S71PL254JC0BAW0Z2 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:Based MCPs |
| S71PL254JC0BAW0Z3 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:Based MCPs |
| S71PL254JC0BAW9Z0 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:Based MCPs |
| S71PL254JC0BAW9Z2 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:Based MCPs |
发布紧急采购，3分钟左右您将得到回复。