- 您现在的位置：买卖IC网 > PDF目录271228 > S71PL254JC0BAITU3 (SPANSION LLC) SPECIALTY MEMORY CIRCUIT, PBGA84 PDF资料下载
参数资料
| 型号： | S71PL254JC0BAITU3 |
| 厂商： | SPANSION LLC |
| 元件分类： | 存储器 |
| 英文描述： | SPECIALTY MEMORY CIRCUIT, PBGA84 |
| 封装： | 8 X 11.60 MM, 1.40 MM HEIGHT, FBGA-84 |
| 文件页数： | 158/188页 |
| 文件大小： | 5078K |
| 代理商： | S71PL254JC0BAITU3 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页当前第158页第159页第160页第161页第162页第163页第164页第165页第166页第167页第168页第169页第170页第171页第172页第173页第174页第175页第176页第177页第178页第179页第180页第181页第182页第183页第184页第185页第186页第187页第188页
70
S29PL127J/S29PL064J/S29PL032J for MCP
S29PL127_064_032J_00_A1 May 21, 2004
Prelimin ary
Once the Password Unlock command is entered, the RY/BY# indicates that the
device is busy. Approximately 1 s is required for each portion of the unlock. Once
the first portion of the password unlock completes (RY/BY# is not low or DQ6
does not toggle when read), the next part of the password is written. The system
must thus monitor RY/BY# or the status bits to confirm when to write the next
portion of the password. Seven cycles are required to successfully clear the PPB
Lock Bit.
PPB Program Command
The PPB Program command is used to program, or set, a given PPB. Each PPB is
individually programmed (but is bulk erased with the other PPBs). The specific
sector address (A22–A12) are written at the same time as the program command
60h with A6 = 0. If the PPB Lock Bit is set and the corresponding PPB is set for
the sector, the PPB Program command will not execute and the command will
time-out without programming the PPB.
After programming a PPB, two additional cycles are needed to determine whether
the PPB has been programmed with margin. If the PPB has been programmed
without margin, the program command should be reissued to improve the pro-
gram margin. Also note that the total number of PPB program/erase cycles is
limited to 100 cycles. Cycling the PPBs beyond 100 cycles is not guaranteed.
The PPB Program command does not follow the Embedded Program algorithm.
All PPB Erase Command
The All PPB Erase command is used to erase all PPBs in bulk. There is no means
for individually erasing a specific PPB. Unlike the PPB program, no specific sector
address is required. However, when the PPB erase command is written all Sector
PPBs are erased in parallel. If the PPB Lock Bit is set the ALL PPB Erase command
will not execute and the command will time-out without erasing the PPBs. After
erasing the PPBs, two additional cycles are needed to determine whether the PPB
has been erased with margin. If the PPBs has been erased without margin, the
erase command should be reissued to improve the program margin.
It is the responsibility of the user to preprogram all PPBs prior to issuing the All
PPB Erase command. If the user attempts to erase a cleared PPB, over-erasure
may occur making it difficult to program the PPB at a later time. Also note that
the total number of PPB program/erase cycles is limited to 100 cycles. Cycling the
PPBs beyond 100 cycles is not guaranteed.
DYB Write Command
The DYB Write command is used for setting the DYB, which is a volatile bit that
is cleared at reset. There is one DYB per sector. If the PPB is set, the sector is
protected regardless of the value of the DYB. If the PPB is cleared, setting the
DYB to a 1 protects the sector from programs or erases. Since this is a volatile
bit, removing power or resetting the device will clear the DYBs. The bank address
is latched when the command is written.
PPB Lock Bit Set Command
The PPB Lock Bit set command is used for setting the DYB, which is a volatile bit
that is cleared at reset. There is one DYB per sector. If the PPB is set, the sector
is protected regardless of the value of the DYB. If the PPB is cleared, setting the
DYB to a 1 protects the sector from programs or erases. Since this is a volatile
相关PDF资料 |
PDF描述 |
|---|---|
| S71PL032JF0BFW074 | SPECIALTY MEMORY CIRCUIT, PBGA56 |
| S29AL016D90MFN011 | 1M X 16 FLASH 3V PROM, 90 ns, PDSO44 |
| SM-5MIN-A-TL-26 | RF COAXIAL RELAY, SP5T, FAILSAFE, 2875mW (COIL), 26500MHz, PANEL MOUNT |
| SM-5MIN-A-TL | RF COAXIAL RELAY, SP5T, FAILSAFE, 2875mW (COIL), 18000MHz, PANEL MOUNT |
| SM-5MIN-A | RF COAXIAL RELAY, SP5T, FAILSAFE, 2875mW (COIL), 18000MHz, PANEL MOUNT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| S71PL254JC0BAW0Z0 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:Based MCPs |
| S71PL254JC0BAW0Z2 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:Based MCPs |
| S71PL254JC0BAW0Z3 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:Based MCPs |
| S71PL254JC0BAW9Z0 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:Based MCPs |
| S71PL254JC0BAW9Z2 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:Based MCPs |
发布紧急采购，3分钟左右您将得到回复。