- 您现在的位置：买卖IC网 > PDF目录16381 > SI2401FS10-EVB (Silicon Laboratories Inc)BOARD EVAL SI2401 UART INTERFACE PDF资料下载
参数资料
| 型号： | SI2401FS10-EVB |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 11/76页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL SI2401 UART INTERFACE |
| 标准包装： | 1 |
| 系列： | ISOmodem® |
| 主要目的： | 电信，调制解调器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | SI2401 |
| 主要属性： | 双路 RJ-11 连接至电话线路，音频连接器 |
| 次要属性： | RS-232，TTL 串行和 USB 接口 |
| 已供物品： | 板，调制解调器，电源 |
| 相关产品： | 336-1095-ND - IC ISOMODEM SYSTEM-SIDE 16SOIC |
| 其它名称： | 336-1167 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页
Si2401
Rev. 1.0
19
4.5. Parallel Phone Detection
The ISOmodem chipset is able to detect when another
telephone, modem, or other device is using the phone
line. This allows the host to avoid interrupting another
phone call when the phone line is already in use and to
intelligently handle an interruption when the ISOmodem
chipset is using the phone line.
4.5.1. On-Hook Intrusion Detection
When the ISOmodem chipset is sharing the telephone
line with other devices, it is important that it not interrupt
a call in progress. To detect when another device is
using the shared telephone line, the host can use the
ISOmodem chipset to monitor the TIP-RING dc voltage
with the LVS[7:0] bits (SDB). The LVS[7:0] bits have a
resolution
of
1 V
per
bit
with
an
accuracy
of
approximately ±10%. Bits 0 through 6 of this 8-bit signed
2s complement number indicate the value of the line
voltage, and the sign bit (bit 7) indicates the polarity of
TIP and RING.
When all devices on a particular telephone line are on-
hook, there is no loop current flowing through TIP and
RING. Therefore, the voltage across TIP and RING is at
a maximum. (On most telephone lines, this on-hook
voltage is a minimum of 40 V.) Once a device goes off-
hook, current flows through TIP and RING on that
device, and the TIP-RING voltage drops appreciably.
(On most telephone lines, this off-hook voltage is a
maximum of 20 V.)
If the host checks the TIP-RING voltage via LVS before
causing the ISOmodem chipset to dial out or go off-
hook, the host can determine if another device is using
the telephone line. One way to do this is to verify that
the voltage represented in LVS is above some fixed
threshold, such as 30 V.
4.5.2. Off-Hook Intrusion Detection
After it has been determined that it is safe to use the
phone line without interrupting a call, the host can
instruct the ISOmodem chipset to begin a call or go off-
hook. However, once the call has begun and the
ISOmodem chipset is in data mode, the serial port is
used for modem data making it difficult for the host to
monitor registers. Therefore, when the ISOmodem
chipset is off-hook, an algorithm is implemented to
automatically monitor the TIP-RING loop current via the
LCS register (SF3). Because the TIP-RING voltage
drops significantly when off-hook, TIP-RING current is a
better indicator of another device using the phone line.
The LCS[7:0] bits have a resolution of 1.1 mA per bit.
An LCS register value of 0x00 indicates less than the
required loop current is present, and a value of 0xFF
indicates excessive current draw (>120 mA if ILIM = 0
or >60 mA if ILIM = 1). The user can read these bits
directly through the LCS register. Upon detecting an
intrusion, an "i" result code is sent to the host if it is in
the
call
negotiation
stage
or
command
mode.
Otherwise, the modem can be programmed to generate
an interrupt to notify the host of the intrusion.
The off-hook intrusion algorithm monitors the value of
LCS (SF3) at a sample rate determined by the DGSR
(SDF, bits 6:0) register (40 ms units). The algorithm
compares each LCS sample to the reference value in
the ACL register (S12). If LCS is lower than ACL by an
amount greater than DCL (S11, bits 4:0), the algorithm
waits for another LCS sample, and if the next LCS
sample is also lower than ACL by an amount greater
than
DCL,
an
interrupt
occurs.
This
helps
the
ISOmodem chipset avoid a false parallel phone
detection (PPD) interrupt due to glitches on the phone
line. The ACL is continually updated with the value of
LCS as outlined below. The algorithm can be outlined
as follows:
If
LCS(t)=LCS(t –40msxDGSR)
and
LCS(t) – ACL > DCL
then ACL = LCS(t)
If
(ACL–LCS[t –40msxDGSR]) > DCL)
and
(ACL – LCS[t]) > DCL)
Then, an intrusion is sent to the host.
The very first sample of LCS the algorithm uses after
going off-hook does not have any previous samples for
comparison. If LCS was measured during a previous
call, this value of LCS may be used as an initial
reference. ACL may be written by the host with this
known value of LCS. If ACL is non-zero, the ISOmodem
chipset uses ACL as the first valid LCS sample in the
off-hook intrusion algorithm. If ACL is 0 (default after
reset), the ISOmodem chipset ignores the register and
does not begin operating the algorithm until two LCS
samples have been received. Additionally, immediately
after a modem call, ACL is updated automatically with
the last valid LCS value before a parallel phone
detection (PPD) intrusion or going back on-hook.
The off-hook intrusion algorithm does not begin to
operate immediately after going off-hook. This is to
avoid triggering an interrupt due to transients resulting
from the ISOmodem chipset itself going from on-hook to
off-hook. The time that elapses between the ISOmodem
chipset going off-hook and the intrusion algorithm
starting defaults to one second and may be adjusted via
the IST register (S82, bits 7:4). If ACL is written to a
non-zero value before going off-hook, a parallel phone
intrusion that occurs during this IST interval and
相关PDF资料 |
PDF描述 |
|---|---|
| UPA0J272MPD1TD | CAP ALUM 2700UF 6.3V 20% RADIAL |
| UPA0J222MPD1TD | CAP ALUM 2200UF 6.3V 20% RADIAL |
| GBC19DRAS | CONN EDGECARD 38POS R/A .100 SLD |
| CM322522-2R2JL | INDUCTOR CHIP 2.2UH 3225 SMD |
| RR70G821MDN1 | CAP ALUM 820UF 4V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SI2401-FSR | 功能描述:电信线路管理 IC 2400b/s System Side 3rd Gen DAA Tech RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| SI2401URT-EVB | 功能描述:网络开发工具 U 634-SI2401FS10-EVB RoHS:否 制造商:Rabbit Semiconductor 产品:Development Kits 类型:Ethernet to Wi-Fi Bridges 工具用于评估:RCM6600W 数据速率:20 Mbps, 40 Mbps 接口类型:802.11 b/g, Ethernet 工作电源电压:3.3 V |
| SI2403 | 制造商:SILABS 制造商全称:SILABS 功能描述:V.22BIS ISOMODEM CHIPSET WITH ERROR CORRECTION |
| SI2403-FT | 制造商:Silicon Laboratories Inc 功能描述:MODEM CHIP CHIPSET ISOMODEM 2.4KBPS 24TSSOP - Rail/Tube |
| SI2404 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:V.90, V.34, V.32BIS, V.22BIS ISOMODEM?? WITH GLOBAL DAA |
发布紧急采购，3分钟左右您将得到回复。