- 您现在的位置：买卖IC网 > PDF目录16381 > SI2401FS10-EVB (Silicon Laboratories Inc)BOARD EVAL SI2401 UART INTERFACE PDF资料下载
参数资料
| 型号： | SI2401FS10-EVB |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 19/76页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL SI2401 UART INTERFACE |
| 标准包装： | 1 |
| 系列： | ISOmodem® |
| 主要目的： | 电信，调制解调器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | SI2401 |
| 主要属性： | 双路 RJ-11 连接至电话线路，音频连接器 |
| 次要属性： | RS-232，TTL 串行和 USB 接口 |
| 已供物品： | 板，调制解调器，电源 |
| 相关产品： | 336-1095-ND - IC ISOMODEM SYSTEM-SIDE 16SOIC |
| 其它名称： | 336-1167 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页
Si2401
26
Rev. 1.0
I
Chip Identification
This command causes the modem to echo the chip
revision for the Si2401 device.
A = Revision A
B = Revision B
C = Revision C, etc.
I6
Display the ISOmodem model number.
“2401” = Si2401.
:I
Interrupt Read
This command causes the ISOmodem chipset to report
the contents of the interrupt status register (S09). The
WOR, PPD, NLD, RI, OCD, and REV bits are also
cleared, and the INT is deactivated on this read.
M
Speaker On/Off Options
These options are used to control AOUT for use with a
call progress monitor speaker.
M0
Speaker always off.
M1
Speaker on until carrier established. The modem sets
SF4[3:2] (ARL) = 11b and SF4[1:0] (ATL) = 11b after a
connection is established.
M2
Speaker always on.
M3
Speaker on after last digit dialed, off at carrier detect.
O
Return to Online Mode
This command returns the modem to the online mode. It
is frequently used after an escape sequence to resume
communication with the remote modem.
RO
Turn-Around
This command initiates a V.23 “direct turnaround”
sequence and returns online.
S
S Register Control
SR=N
Write an S register. This command writes the value “N”
to the S-register specified by “R”. “R” is a hexidecimal
number, and “N” must also be a hexadecimal number
from 00–FF. This command does not wait for a carriage
return <CR> before taking effect.
Note:
Two digits must always be entered for both “R” and “N”.
SR?
Read an S register. This command causes the Si2401
to echo the value of the S-register specified by R in hex
format. R must be a hexidecimal number.
Note:
Two digits must always be entered for R.
w##
Write S Register in Binary
This command writes a register in binary format. The
first byte following the “w” is the address in binary
format, and the second byte is the data in binary format.
This is a more rapid method to write registers than the
“SR=N” command and is recommended for use by a
host microcontroller.
r#
Read S Register in Binary
This command reads a register in binary format. The
byte following the “r” is the address in binary format.
The modem echoes the contents of this register in
binary format. This is a more rapid method to read
registers
than
the
“SR?”
command
and
is
recommended for use by a host microcontroller. Modem
result codes should be disabled to avoid confusing a
result code with the value being read. (S62 = 40).
Notes:
1. w## and r# are not required to be on separate lines (i.e.,
no <CR> between them). Also, the result of an r# is
returned immediately without waiting for a <CR> at the end
of the AT command line.
2. Once a <CR> is encountered, “AT” is again required to
begin the next “AT” command.
m#
Monitor S Register in Binary
This command monitors a register in binary format. The
byte following the “m” is the address in binary format.
The Si2401 constantly transmits the contents of the
register at the set baud rate until a new byte is
transmitted to the device. The new byte is ignored and
viewed as a stop command. The modem result codes
should be disabled (as described above in r#) before
using this command.
q#
Read S Register in Binary
This command is exactly the same as the r# command;
however, the response from the Si2401 is formatted as
0x55 followed by the contents of the register in binary.
This guarantees that the register contents are always
preceded by 0x55 and allows the result codes to remain
enabled.
V
Result Code Options
V0
Result codes reported according to Table 14.
V1
Result codes reported with an additional carriage return
and line feed (default).
相关PDF资料 |
PDF描述 |
|---|---|
| UPA0J272MPD1TD | CAP ALUM 2700UF 6.3V 20% RADIAL |
| UPA0J222MPD1TD | CAP ALUM 2200UF 6.3V 20% RADIAL |
| GBC19DRAS | CONN EDGECARD 38POS R/A .100 SLD |
| CM322522-2R2JL | INDUCTOR CHIP 2.2UH 3225 SMD |
| RR70G821MDN1 | CAP ALUM 820UF 4V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SI2401-FSR | 功能描述:电信线路管理 IC 2400b/s System Side 3rd Gen DAA Tech RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| SI2401URT-EVB | 功能描述:网络开发工具 U 634-SI2401FS10-EVB RoHS:否 制造商:Rabbit Semiconductor 产品:Development Kits 类型:Ethernet to Wi-Fi Bridges 工具用于评估:RCM6600W 数据速率:20 Mbps, 40 Mbps 接口类型:802.11 b/g, Ethernet 工作电源电压:3.3 V |
| SI2403 | 制造商:SILABS 制造商全称:SILABS 功能描述:V.22BIS ISOMODEM CHIPSET WITH ERROR CORRECTION |
| SI2403-FT | 制造商:Silicon Laboratories Inc 功能描述:MODEM CHIP CHIPSET ISOMODEM 2.4KBPS 24TSSOP - Rail/Tube |
| SI2404 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:V.90, V.34, V.32BIS, V.22BIS ISOMODEM?? WITH GLOBAL DAA |
发布紧急采购，3分钟左右您将得到回复。