- 您现在的位置：买卖IC网 > PDF目录16381 > SI2401FS10-EVB (Silicon Laboratories Inc)BOARD EVAL SI2401 UART INTERFACE PDF资料下载
参数资料
| 型号： | SI2401FS10-EVB |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 21/76页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL SI2401 UART INTERFACE |
| 标准包装： | 1 |
| 系列： | ISOmodem® |
| 主要目的： | 电信，调制解调器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | SI2401 |
| 主要属性： | 双路 RJ-11 连接至电话线路，音频连接器 |
| 次要属性： | RS-232，TTL 串行和 USB 接口 |
| 已供物品： | 板，调制解调器，电源 |
| 相关产品： | 336-1095-ND - IC ISOMODEM SYSTEM-SIDE 16SOIC |
| 其它名称： | 336-1167 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页
Si2401
28
Rev. 1.0
send the first SIA block after the “c” is received. Once
the block is transmitted, the modem can monitor for the
acknowledge
tone
by
completing
the
following
sequence:
1. Place the Si2401 in command mode by pulsing the
ESCAPE pin (Si2401 pin 14). The “+++” and “ninth-
bit” escape modes operate in the “!2” mode but are
not recommended because they can send unwanted
characters to the remote modem.
2. Issue the “ATX1” command to turn the modem
transmitter off and begin monitoring for the
acknowledgment tones.
3. Monitor for a positive (negative) acknowledgment “P”
(“N”) after the tone has been detected for at least
400 ms.
4. The modem, still in command mode, can be placed
online as a transmitter by issuing the “ATX2”
command or a receiver by issuing the “ATX3”
command. If tonal acknowledgement is not used, the
host can toggle the ESCAPE pin to place the Si2401
in the command mode and issue an “ATX2” or an
“ATX3” command to reverse data direction.
This sequence can be repeated for long messages.
5.5. Modem Result Codes and Call
Progress
Table 14 shows the modem result codes that can be
used in call progress monitoring. All result codes are a
single character to speed up communication and ease
host processing.
Table 14. Modem Result Codes
Command
Function
a
British Telecom Caller ID Idle Tone
Alert Detected
b
Busy Tone Detected
c
Connect
d
Connect 1200 bps (when pro-
grammed as V.22bis modem)
f
Hookswitch Flash or Battery Reversal
Detected
H
Modem Automatically Hanging Up in
!2, !1
I
Intrusion Completed (parallel phone
back on-hook)
i
Intrusion Detected (parallel phone off-
hook on the line)
K
Kissoff Tone Detected
k
Contact ID Kissoff Tone too long (!1)
L
Phone Line Detected
l
No Phone Line Detected
m
Caller ID Mark Signal Detected
NNo Carrier Detected
n
No Dial tone (time-out set by CW
[S02])
O
Modem OK Response
R
Incoming Ring Signal Detected
r
Ringback Tone Detected
t
Dial Tone
v
Connect 75 bps TX (V.23 originate
only)
x
Overcurrent State Detected After an
Off-Hook Event
^
Kissoff tone detection required
,
Dialing Complete
相关PDF资料 |
PDF描述 |
|---|---|
| UPA0J272MPD1TD | CAP ALUM 2700UF 6.3V 20% RADIAL |
| UPA0J222MPD1TD | CAP ALUM 2200UF 6.3V 20% RADIAL |
| GBC19DRAS | CONN EDGECARD 38POS R/A .100 SLD |
| CM322522-2R2JL | INDUCTOR CHIP 2.2UH 3225 SMD |
| RR70G821MDN1 | CAP ALUM 820UF 4V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SI2401-FSR | 功能描述:电信线路管理 IC 2400b/s System Side 3rd Gen DAA Tech RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| SI2401URT-EVB | 功能描述:网络开发工具 U 634-SI2401FS10-EVB RoHS:否 制造商:Rabbit Semiconductor 产品:Development Kits 类型:Ethernet to Wi-Fi Bridges 工具用于评估:RCM6600W 数据速率:20 Mbps, 40 Mbps 接口类型:802.11 b/g, Ethernet 工作电源电压:3.3 V |
| SI2403 | 制造商:SILABS 制造商全称:SILABS 功能描述:V.22BIS ISOMODEM CHIPSET WITH ERROR CORRECTION |
| SI2403-FT | 制造商:Silicon Laboratories Inc 功能描述:MODEM CHIP CHIPSET ISOMODEM 2.4KBPS 24TSSOP - Rail/Tube |
| SI2404 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:V.90, V.34, V.32BIS, V.22BIS ISOMODEM?? WITH GLOBAL DAA |
发布紧急采购，3分钟左右您将得到回复。