- 您现在的位置：买卖IC网 > PDF目录16381 > SI2401FS10-EVB (Silicon Laboratories Inc)BOARD EVAL SI2401 UART INTERFACE PDF资料下载
参数资料
| 型号： | SI2401FS10-EVB |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 18/76页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL SI2401 UART INTERFACE |
| 标准包装： | 1 |
| 系列： | ISOmodem® |
| 主要目的： | 电信，调制解调器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | SI2401 |
| 主要属性： | 双路 RJ-11 连接至电话线路，音频连接器 |
| 次要属性： | RS-232，TTL 串行和 USB 接口 |
| 已供物品： | 板，调制解调器，电源 |
| 相关产品： | 336-1095-ND - IC ISOMODEM SYSTEM-SIDE 16SOIC |
| 其它名称： | 336-1167 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页
Si2401
Rev. 1.0
25
5.3. AT Command Set Description
AAnswer
The “A” command makes the modem go off-hook and
respond to an incoming call. This command is to be
executed after the Si2401 has indicated a ring has
occurred. (The Si2401 indicates an incoming ring by
echoing an “R”.)
This command is aborted if any other character is
transmitted to the Si2401 before the answer process is
completed.
Auto answer mode is entered by setting S00 (NR) to a
non-zero value. NR indicates the number of rings before
answering the line.
Upon
answering,
the
modem
communicates
by
whatever protocol has been determined via the modem
control registers in S07 (MF1).
If no transmit carrier signal is received from the calling
modem within the time specified in S39 (CDT), the
modem hangs up and enters the idle state.
DDial
DT#
Tone Dial Number.
DP#
Pulse Dial Number.
The D commands make the modem dial a telephone
call according to the digits and dial modifiers in the dial
string following the command. A maximum of 64 digits is
allowed. A DT command performs tone dialing, and a
DP command performs pulse dialing.
The ATH1 command can be used to go off-hook without
detecting a dial tone or dialing.
The dial string must contain only the digits “0–9”, “*”, “#”,
“A”, “B”, “C”, “D”, or the modifiers “;”, “/”, or “,”. Other
characters are interpreted incorrectly. The modifier “,”
causes a two-second delay (added to the spacing value
in S04) in dialing. The modifier “/” causes a 125 ms
delay (added to the spacing value in S04) in dialing. The
modifier “;” returns the device to command mode after
dialing and must be the last character.
If any character is received by the Si2401 between the
ATDT#<CR> (or ATDP#<CR>) command and when the
connection is made (“c” or “d” is echoed), the extra
character is interpreted as an abort, and the Si2401
returns to command mode ready to accept AT
commands. A line feed character immediately following
the <CR> is treated as an “extra character” and aborts
the call.
If the modem does not have to dial (i.e., “ATDT<CR>” or
“ATDP<CR>” with no dial string), the Si2401 assumes
the call was manually established and attempts to make
a connection.
5.3.1. Automatic Tone/Pulse Dialing
The Si2401 can be configured to attempt DTMF dialing
and automatically revert to pulse dialing if it determines
that the line is not DTMF-capable. This feature is best
explained by the following example.
If it is desired that the telephone number, 12345, be
dialed, it is normally accomplished through either the
ATDT12345 or the ATDP12345 command. In the force
pulse dialing mode of operation, the following string
should be issued instead: ATDT1,p12345
If the result code returned is “t,”, this indicates that the
dialing was accomplished using DTMF dialing. If the
result code returned is “tt,”, it indicates that the dialing
was accomplished using pulse dialing.
In the above example, the Si2401 dials the first digit “1”
using DTMF dialing. The “,” is used to pause in order to
ensure that the central office has had time to accept the
DTMF digit “1”. When the Si2401 processes the “p”
command, it attempts to detect a dial tone. If a dial tone
is detected, the DTMF digit “1” was not effective; hence,
the line does not support DTMF dialing. Conversely, if
the dial tone is not detected, the DTMF digit “1” was
effective, and the line supports DTMF dialing. The
character after the “p” may or may not be dialed
depending on whether the DTMF digit “1” was effective.
If the “1” was effective (DTMF mode), the character after
the “p” is skipped. The next DTMF digit to be dialed is
“2”. Subsequent digits are all DTMF. If the “1” was not
effective, the first character after the “p” (the “1”) is
pulse-dialed, and subsequent digits are all pulse-dialed.
E
Command Mode Echo
Tells the Si2401 whether or not to echo characters sent
from the terminal.
EO
Does not echo characters sent from the terminal.
E1
Echoes characters sent from the terminal.
H0
Hangup
Hang up and go into command mode (go offline).
H1
Off-hook
Go off-hook and remain in command mode.
q#
Read S-Register in binary
V0
Result code with no carriage return
V1
Result code with added carriage
returns
Z
Software reset
z
Wakeup on ring
Table 12. AT Command Set Summary
相关PDF资料 |
PDF描述 |
|---|---|
| UPA0J272MPD1TD | CAP ALUM 2700UF 6.3V 20% RADIAL |
| UPA0J222MPD1TD | CAP ALUM 2200UF 6.3V 20% RADIAL |
| GBC19DRAS | CONN EDGECARD 38POS R/A .100 SLD |
| CM322522-2R2JL | INDUCTOR CHIP 2.2UH 3225 SMD |
| RR70G821MDN1 | CAP ALUM 820UF 4V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SI2401-FSR | 功能描述:电信线路管理 IC 2400b/s System Side 3rd Gen DAA Tech RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| SI2401URT-EVB | 功能描述:网络开发工具 U 634-SI2401FS10-EVB RoHS:否 制造商:Rabbit Semiconductor 产品:Development Kits 类型:Ethernet to Wi-Fi Bridges 工具用于评估:RCM6600W 数据速率:20 Mbps, 40 Mbps 接口类型:802.11 b/g, Ethernet 工作电源电压:3.3 V |
| SI2403 | 制造商:SILABS 制造商全称:SILABS 功能描述:V.22BIS ISOMODEM CHIPSET WITH ERROR CORRECTION |
| SI2403-FT | 制造商:Silicon Laboratories Inc 功能描述:MODEM CHIP CHIPSET ISOMODEM 2.4KBPS 24TSSOP - Rail/Tube |
| SI2404 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:V.90, V.34, V.32BIS, V.22BIS ISOMODEM?? WITH GLOBAL DAA |
发布紧急采购，3分钟左右您将得到回复。