- 您现在的位置：买卖IC网 > PDF目录16381 > SI2401FS10-EVB (Silicon Laboratories Inc)BOARD EVAL SI2401 UART INTERFACE PDF资料下载
参数资料
| 型号： | SI2401FS10-EVB |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 14/76页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL SI2401 UART INTERFACE |
| 标准包装： | 1 |
| 系列： | ISOmodem® |
| 主要目的： | 电信，调制解调器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | SI2401 |
| 主要属性： | 双路 RJ-11 连接至电话线路，音频连接器 |
| 次要属性： | RS-232，TTL 串行和 USB 接口 |
| 已供物品： | 板，调制解调器，电源 |
| 相关产品： | 336-1095-ND - IC ISOMODEM SYSTEM-SIDE 16SOIC |
| 其它名称： | 336-1167 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页
Si2401
Rev. 1.0
21
modem transmitting at 75 bps and receiving at 1200/
600 bps.
The Si2401 supports the V.23 turnaround procedure.
This allows a modem that is transmitting at 75 bps to
initiate a “turnaround” procedure so that it can begin
transmitting data at 1200/600 bps and receiving data at
75 bps. The modem is defined as being in V.23 master
mode if it is transmitting at 75 bps, and it is defined as
being in slave mode if the modem is transmitting at
1200/600 bps. The following paragraphs give a detailed
description of the V.23 turnaround procedure.
4.7.1. Modem in Master Mode
To perform a direct turnaround once a modem
connection is established, the master host goes into
online-command-mode
by
sending
an
escape
command (Escape pin activation, TIES, or ninth bit
escape) to the master modem.
Note:
The host can initiate a turnaround only if the Si2401 is
the master.
The host then sends the ATRO command to the Si2401
to initiate a V.23 turnaround and return to the online
(data) mode.
The Si2401 then changes its carrier frequency (from
390 Hz to 1300 Hz) and waits to detect a 390 Hz carrier
for 440 ms. If the modem detects more than 40 ms of a
390 Hz carrier in a time window of 440 ms, it echoes the
“c” response character. If the modem does not detect
more than 40 ms of a 390 Hz carrier in a time window of
440 ms, it hangs up and echoes the “N” (no carrier)
character as a response.
4.7.2. Modem in Slave Mode
Configure GPIO4 as INT (SE2[7:6] [GPIO4] = 11b). The
Si2401 performs a reverse turnaround when it detects a
carrier drop longer than 20 ms. The Si2401 then
reverses (changes its carrier from 1300 Hz to 390 Hz)
and waits to detect a 1300 Hz carrier for 400 ms. If the
Si2401 detects more than 40 ms of a 1300 Hz carrier in
a time window of 400 ms, it sets the S09[7] bit, and the
next character echoed by the Si2401 is a “v”.
If the Si2401 does not detect more than 40 ms of the
1300 Hz carrier in a time window of 400 ms, it reverses
again and waits to detect a 390 Hz carrier for 440 ms.
Then, if the Si2401 detects more than 40 ms of a
390 Hz carrier in a time window of 220 ms, it sets the
S09[7] bit, and the next character echoed by the Si2401
is a “c”.
At this point, if the Si2401 does not detect more than
40 ms of the 390 Hz carrier in a time window of 440 ms,
it hangs up, sets the S09[7] bit, and the next character
echoed by the Si2401 is an “N” (no carrier).
Successful completion of a turnaround procedure in
master
or
slave
mode
automatically
updates
S07[4] (V23T) and S07[5] (V23R) to indicate the new
status of the V.23 connection.
To avoid using the INT pin, the host may also be notified
of the INT condition by using 9-bit data mode. Setting
S15[0] (NBE) = 1b and S0C[3] (9BF) = 0b configures
the ninth bit on the Si2401 TXD path to function exactly
as the INT pin has been described.
4.8. V.42 HDLC Mode
The Si2401 supports V.42 through hardware HDLC
framing in all modem data modes. Frame packing and
unpacking including opening and closing flag generation
and detection, CRC computation and checking, zero
insertion and deletion, and modem data transmission
and reception are all performed by the Si2401. V.42
error correction and V.42bis data compression must be
performed by the host.
The digital link interface in this mode uses the same
UART interface (8-bit data and 9-bit data formats) as in
the asynchronous modes, and the ninth data bit may be
used as an escape by setting S15[0] (NBE) = 1b. When
using HDLC in 9-bit data mode, if the ninth bit is not
used as an escape, it is ignored.
To use the HDLC feature on the Si2401, the host must
enable HDLC operation by setting S13[1] (HDEN) = 1b.
The host may initiate the call or answer the call using
either the “ATDT#”, the “ATA” command or the auto-
answer mode. (The auto-answer mode is implemented
by setting register S00 (NR) to a non-zero value.) When
the call is connected, a “c”, “d”, or “v” is echoed to the
host controller. The host may now send/receive data
across the UART using either the 8-bit data or 9-bit data
formats with flow control.
At this point, the Si2401 begins framing data into the
HDLC format. On the transmit side, if no data is
available from the host, the HDLC flag pattern is sent
repeatedly.
When
data
is
available,
the
Si2401
computes the CRC code throughout the frame, and the
data is sent with the HDLC zero-bit insertion algorithm.
HDLC flow control operates in a similar manner to
normal asynchronous flow control across the UART and
is shown in Figure 4. To operate flow control (using the
CTS pin to indicate when the Si2401 is ready to accept
a character), a DTE rate higher than the line rate should
be selected.
相关PDF资料 |
PDF描述 |
|---|---|
| UPA0J272MPD1TD | CAP ALUM 2700UF 6.3V 20% RADIAL |
| UPA0J222MPD1TD | CAP ALUM 2200UF 6.3V 20% RADIAL |
| GBC19DRAS | CONN EDGECARD 38POS R/A .100 SLD |
| CM322522-2R2JL | INDUCTOR CHIP 2.2UH 3225 SMD |
| RR70G821MDN1 | CAP ALUM 820UF 4V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SI2401-FSR | 功能描述:电信线路管理 IC 2400b/s System Side 3rd Gen DAA Tech RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| SI2401URT-EVB | 功能描述:网络开发工具 U 634-SI2401FS10-EVB RoHS:否 制造商:Rabbit Semiconductor 产品:Development Kits 类型:Ethernet to Wi-Fi Bridges 工具用于评估:RCM6600W 数据速率:20 Mbps, 40 Mbps 接口类型:802.11 b/g, Ethernet 工作电源电压:3.3 V |
| SI2403 | 制造商:SILABS 制造商全称:SILABS 功能描述:V.22BIS ISOMODEM CHIPSET WITH ERROR CORRECTION |
| SI2403-FT | 制造商:Silicon Laboratories Inc 功能描述:MODEM CHIP CHIPSET ISOMODEM 2.4KBPS 24TSSOP - Rail/Tube |
| SI2404 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:V.90, V.34, V.32BIS, V.22BIS ISOMODEM?? WITH GLOBAL DAA |
发布紧急采购，3分钟左右您将得到回复。