参数资料
型号: SI2401FS10-EVB
厂商: Silicon Laboratories Inc
文件页数: 25/76页
文件大小: 0K
描述: BOARD EVAL SI2401 UART INTERFACE
标准包装: 1
系列: ISOmodem®
主要目的: 电信,调制解调器
嵌入式:
已用 IC / 零件: SI2401
主要属性: 双路 RJ-11 连接至电话线路,音频连接器
次要属性: RS-232,TTL 串行和 USB 接口
已供物品: 板,调制解调器,电源
相关产品: 336-1095-ND - IC ISOMODEM SYSTEM-SIDE 16SOIC
其它名称: 336-1167
Si2401
Rev. 1.0
31
6. Low Level DSP Control
Although not necessary for most applications, the DSP
low-level control functions are available for users with
very specific applications requiring direct DSP control.
6.1. DSP Registers
Several DSP registers are accessible through the
Si2401 microcontroller via S-registers SE5, SE6, and
SE8. SE5 and SE6 are used as conduits to write data to
specific DSP registers and read status. SE8 defines the
function of SE5 and SE6 depending on whether they
are being written to or read from. Care must be
exercised when writing to DSP registers. DSP registers
can only be written while the Si2401 is on-hook and in
the command mode. Writing to any register address not
listed in Tables 18 and 19 or writing out-of-range values
is likely to cause the DSP to exhibit unpredictable
behavior.
The DSP register address is 16-bits wide, and the DSP
data field is 14-bits wide. DSP register addresses and
data are written in hexadecimal. To write a value to a
DSP register, the register address is written, and then
the data is written. When SE8 = 0x00, SE5(DADL) is
written with the low bits [7:0] of the DSP register
address, and SE6 (DADH) is written with the high bits
[15:8]
of
the
DSP
address.
When
SE8 = 0x01,
SE5 (DDL) is written with the low bits [7:0] of the DSP
data word corresponding to the previously written
address, and SE6 (DDH) is written with the high bits
[15:8] of the data word corresponding to the previously
written address. Example 1 illustrates the proper
procedure for writing to DSP registers.
Example1:
The user would like to program call
progress filter coefficient A2_k0 (0x15) to be 309
(0x135).
Host Command:
ATSE8=00SE6=00SE5=15SE8=01SE6=01SE5=35SE8=00
In this command, ATSE8=00 sets up registers SE5 and
SE6 as DSP address registers. SE6=00 sets the high
bits of the address, and SE5=15 sets the low bits.
SE8=01 sets up registers SE5 and SE6 as DSP data
registers for the previously-written DSP address (0x15).
SE6=01 sets the six high bits of the 14-bit data word,
and SE5=35 sets the eight low bits of the 14-bit data
word.
Table 17. DTMF Values
DTMF
Code
Keyboard
Equivalent
Contact
ID
Digit
Tones
Low
High
0
941
1336
1
697
1209
2
697
1336
3
697
1477
4
770
1209
5
770
1336
6
770
1477
7
852
1209
8
852
1336
9
852
1477
10
D
941
1633
11
*
B
941
1209
12
#
C
941
1477
13
A
D
697
1633
14
B
E
770
1633
15
C
F
852
1633
相关PDF资料
PDF描述
UPA0J272MPD1TD CAP ALUM 2700UF 6.3V 20% RADIAL
UPA0J222MPD1TD CAP ALUM 2200UF 6.3V 20% RADIAL
GBC19DRAS CONN EDGECARD 38POS R/A .100 SLD
CM322522-2R2JL INDUCTOR CHIP 2.2UH 3225 SMD
RR70G821MDN1 CAP ALUM 820UF 4V 20% RADIAL
相关代理商/技术参数
参数描述
SI2401-FSR 功能描述:电信线路管理 IC 2400b/s System Side 3rd Gen DAA Tech RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray
SI2401URT-EVB 功能描述:网络开发工具 U 634-SI2401FS10-EVB RoHS:否 制造商:Rabbit Semiconductor 产品:Development Kits 类型:Ethernet to Wi-Fi Bridges 工具用于评估:RCM6600W 数据速率:20 Mbps, 40 Mbps 接口类型:802.11 b/g, Ethernet 工作电源电压:3.3 V
SI2403 制造商:SILABS 制造商全称:SILABS 功能描述:V.22BIS ISOMODEM CHIPSET WITH ERROR CORRECTION
SI2403-FT 制造商:Silicon Laboratories Inc 功能描述:MODEM CHIP CHIPSET ISOMODEM 2.4KBPS 24TSSOP - Rail/Tube
SI2404 制造商:未知厂家 制造商全称:未知厂家 功能描述:V.90, V.34, V.32BIS, V.22BIS ISOMODEM?? WITH GLOBAL DAA