- 您现在的位置：买卖IC网 > PDF目录16381 > SI2401FS10-EVB (Silicon Laboratories Inc)BOARD EVAL SI2401 UART INTERFACE PDF资料下载
参数资料
| 型号： | SI2401FS10-EVB |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 13/76页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL SI2401 UART INTERFACE |
| 标准包装： | 1 |
| 系列： | ISOmodem® |
| 主要目的： | 电信，调制解调器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | SI2401 |
| 主要属性： | 双路 RJ-11 连接至电话线路，音频连接器 |
| 次要属性： | RS-232，TTL 串行和 USB 接口 |
| 已供物品： | 板，调制解调器，电源 |
| 相关产品： | 336-1095-ND - IC ISOMODEM SYSTEM-SIDE 16SOIC |
| 其它名称： | 336-1167 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页
Si2401
20
Rev. 1.0
sustains through the end of the interval triggers an
interrupt.
The off-hook intrusion algorithm may additionally be
disabled for a period of time after dialing begins via the
IB register (S82, bits 2:1). This avoids triggering an
interrupt due to pulse dialing, open-switch intervals, or
line transients from central office switching. Intrusion
may be disabled from the start of dialing to the end of
dialing (IB = 01b), from the start of dialing to the timeout
of the IS (S29, bits 7:0) by setting IB = 10b(IB = 2), or
from the start of dialing to carrier detect by setting
IB = 11b. The off-hook intrusion algorithm is only
suspended (not disabled) during this IB interval.
Therefore, any intrusion that occurs during the IB
interval and sustains through the end of the interval
triggers a PPD interrupt.
4.6. Interrupt Detection
The INT interrupt pin can be programmed to alert the
host of loss of carrier, loss of phone line voltage/current,
parallel phone detection, and other interrupts listed in
the interrupt status mask (S08). After the host receives
an interrupt via the INT pin, the host should issue the
AT:I command. This command causes a read-clear of
the WOR, PPD, NLD, RI, OCD, and REV bits of the S09
register and raises (deactivates) the INT pin. All the
interrupt status bits in register S09 remain high after
being set until cleared by the AT:I command.
4.6.1. Loop Current Detection
In addition to monitoring parallel phone intrusion, it is
possible to monitor the loss of loop current. This feature
can be enabled by setting S08[4] (NLDM) = 1. This
feature is disabled by default. If the loop current is too
low for normal DAA operation, S09[4] (NLD) is set.
During this event, if the NLR result code is enabled by
setting S62[1](NLR) = 1, the “l” result code is sent. Once
the loop current returns to a normal current state, the “L”
result code is sent. The INT pin is also asserted if
enabled.
4.6.2. Loss-of-Carrier Detection
The Si2401 has two methods of implementing a loss-of-
carrier function. If GPIO4 is programmed as INT, and if
S08[7](CDM) = 1, INT asserts in data mode when a
loss-of-carrier is detected. The carrier detect function
may also be implemented on GPIO2 by setting SE2[3:2]
(GPIO2) = 01 and SOC[7](CDE) = 1.
4.6.3. Overcurrent Detection
The Si2401 has an integrated overcurrent detection
feature.
The
Si2401
begins
monitoring
for
an
overcurrent condition at a programmable time set by
S32 (OCDT) after going off-hook (default = 20 ms). If an
overcurrent condition is detected, the Si2401 sets
S09[1]
interrupt
status.
As
long
as
GPIO4
is
programmed as INT and the overcurrent mask bit is
enabled by setting S08[1](OCDM) = 1, INT asserts
during an overcurrent situation. The host may then
check S09[1] (OCD) via the AT:I command to confirm
that an overcurrent condition occurred.
4.6.4. Caller ID Decoding Operation
The Si2401 supports full caller ID detection and decode
for US Bellcore and UK standards. To use the caller ID
decoding
feature,
the
following
configuration
is
necessary:
1. Set SE0[3] (ND) = 0b (set modem to 8N1
configuration).
2. Set S0C[6:5] (CIDM) = 01 (set modem to Bellcore
type caller ID) or S13[2] (CIDB) = 1 (set modem to
UK type caller ID).
4.6.5. Caller ID Monitor/Bellcore Caller ID
The Si2401 continuously monitors the phone line for the
caller ID mark signals. This can be useful in systems
that require detection of caller ID data before the ring
signal, voice mail indicator signals, and Type II caller ID
monitor support. To force the Si2401 into caller ID
monitor mode, set SOC[6:5] (CIDM) = 11.
Note:
CIDM should be disabled before going off-hook.
4.6.6. UK Caller ID Operation
The Si2401 starts searching for the Idle State Tone Alert
Signal. When this signal has been detected, the Si2401
transmits an “a” to the host. After the Idle State Tone
Alert Signal is completed, the Si2401 applies the
wetting pulse for the required 15 ms by quickly going
off-hook and on-hook. From this point on, the algorithm
is identical to that of Bellcore in that it searches for the
channel seizure signal and the marks before echoing an
“m” and then reports the decoded caller ID data.
4.7. V.23 Operation/V.23 Reversing
The Si2401 supports full V.23 operation including the
V.23 reversing procedure. V.23 operation is enabled by
setting
S07
(MF1) = xx10x110b or xx01x110b. If
S07[5] (V23R) = 1b, the Si2401 transmits data at 75 bps
and
receives
data
at
600
or
1200 bps.
If
S07[4] (V23T) = 1b, the Si2401 receives data at 75 bps
and transmits data at 600 or 1200 bps. S07[2] (BAUD)
is the 1200 or 600 bps indicator. BAUD = 1b enables the
1200/600 V.23 channel to run at 1200 bps, while
BAUD = 0b enables 600 bps operation.
When a V.23 connection is successfully established, the
modem responds with a “c” character if the connection
is made with the modem transmitting at 1200/600 bps
and receiving at 75 bps. The modem responds with a
“v” character if a V.23 connection is established with the
相关PDF资料 |
PDF描述 |
|---|---|
| UPA0J272MPD1TD | CAP ALUM 2700UF 6.3V 20% RADIAL |
| UPA0J222MPD1TD | CAP ALUM 2200UF 6.3V 20% RADIAL |
| GBC19DRAS | CONN EDGECARD 38POS R/A .100 SLD |
| CM322522-2R2JL | INDUCTOR CHIP 2.2UH 3225 SMD |
| RR70G821MDN1 | CAP ALUM 820UF 4V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SI2401-FSR | 功能描述:电信线路管理 IC 2400b/s System Side 3rd Gen DAA Tech RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| SI2401URT-EVB | 功能描述:网络开发工具 U 634-SI2401FS10-EVB RoHS:否 制造商:Rabbit Semiconductor 产品:Development Kits 类型:Ethernet to Wi-Fi Bridges 工具用于评估:RCM6600W 数据速率:20 Mbps, 40 Mbps 接口类型:802.11 b/g, Ethernet 工作电源电压:3.3 V |
| SI2403 | 制造商:SILABS 制造商全称:SILABS 功能描述:V.22BIS ISOMODEM CHIPSET WITH ERROR CORRECTION |
| SI2403-FT | 制造商:Silicon Laboratories Inc 功能描述:MODEM CHIP CHIPSET ISOMODEM 2.4KBPS 24TSSOP - Rail/Tube |
| SI2404 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:V.90, V.34, V.32BIS, V.22BIS ISOMODEM?? WITH GLOBAL DAA |
发布紧急采购，3分钟左右您将得到回复。