- 您现在的位置：买卖IC网 > PDF目录16381 > SI2401FS10-EVB (Silicon Laboratories Inc)BOARD EVAL SI2401 UART INTERFACE PDF资料下载
参数资料
| 型号： | SI2401FS10-EVB |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 20/76页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL SI2401 UART INTERFACE |
| 标准包装： | 1 |
| 系列： | ISOmodem® |
| 主要目的： | 电信，调制解调器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | SI2401 |
| 主要属性： | 双路 RJ-11 连接至电话线路，音频连接器 |
| 次要属性： | RS-232，TTL 串行和 USB 接口 |
| 已供物品： | 板，调制解调器，电源 |
| 相关产品： | 336-1095-ND - IC ISOMODEM SYSTEM-SIDE 16SOIC |
| 其它名称： | 336-1167 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页
Si2401
Rev. 1.0
27
Z
Software Reset
The “Z” command initiates a software reset causing all
registers, with the exception of E0, which controls the
DTE settings, to default to their powerup value.
The hardware reset pin, RESET (Si2401, pin 8), is used
to reset the Si2401 to factory default settings.
z
Wakeup on Ring (lower-case z)
The Si2401 enters a low-power mode in which the DSP
and microcontroller are powered down. In this mode,
only the line-side device (Si3010) and the isolation
capacitor
communication
link
are
functional.
An
incoming ring signal or line transient causes the Si2401
to power up and echo an “R”. Any character received on
the RXD pin also causes the Si2401 to exit the wakeup-
on-ring state. Return from wake-on-ring can also be set
to trigger the INT pin by setting S08[6] (WORM) = 1b.
5.4. Alarm Industry AT Commands
The Si2401 supports a complete set of commands
necessary for making connections in security industry
systems. The Si2401 is configurable in two modes for
these
applications.
The
first
mode
uses
DTMF
messaging and is selected with the “!1” command. The
second
mode
uses
FSK
transmit
with
a
tone
acknowledgement and is selected with “!2”.
The following are a few general comments about the
use of “!” commands. Specific details for each command
are given below. The first instance of the “!” must be on
the same line as the ATDT or ATDP command. DRT
must be set to data mode (SE4[5:4] (DRT) = 0b) before
attempting to send tones after a “!” command. The three
data-mode escape sequences (“+++”, “escape” pin, and
“ninth-bit”) function in “!2” mode. However, using the
“+++” or “ninth-bit” is not recommended because
characters could be sent to and misinterpreted by the
remote modem. Only the “escape pin” (Si2401, pin 14)
is recommended for use in the “!2” mode. The “!1” mode
has a special escape provision described below. The AT
commands
for
Alarm
Industry
applications
are
described in Table 13.
5.4.1. !1
Dial number and follow the DTMF security protocol.
The format for this command is as follows:
ATDT<phone number>!1<message 1><CR>
K
!<message 2><CR>
K
!<message 3><CR>
K
!<message n><CR>
The modem dials the phone number and echoes “r”
(ring), “b” (busy), and “c” (connect) as appropriate. “c”
echoes only after the Si2401 detects the Handshake
Tone. After a 250 ms delay, the modem sends the
DTMF tones containing the first message data and
listens for a Kissoff Tone. If a Kissoff Tone shorter than
or
equal
to
the
value
stored
in
S36(KTL)
(default = 480 ms) is detected, the Si2401 echoes a “K”.
A “k” is echoed if the length of the Kissoff Tone is longer
than the S36(KTL) value. The controller can then send
the next message. All messages must be preceded by a
“!” and followed by a <CR> and received by the Si2401
within
250 ms
after
the
“K”
is
echoed.
Setting
S0C[0] (MCH) = 1b causes a “.” to be echoed when the
DTMF tone is turned on and a “/” character to be
echoed when the DTMF tone is turned off. This helps
the host monitor the status of the message being sent.
The previous message can be resent if the host
responds with a “~” after the Si2401 echoes a “K”. Any
character other than a “!” or a “~” sent to the modem
immediately after the “K” causes the modem to escape
to the command mode and remain off-hook. Any
character except “!” and “~” sent during the transmission
of a message causes the message to be aborted and
the modem to return to the command mode.
If the Kissoff Tone is not received within 1.25 seconds,
the modem echoes a “^”. A “~” from the host causes the
last message to be resent. Any character other than a
“!” or a “~” sent to the modem immediately after the “^”
causes the modem to escape to the command mode
and remain off-hook.
5.4.2. !2
Dial the number and follow the “SIA Format” protocol for
Alarm System Communications.
The modem dials the phone number and echoes “r”
(ring), “b” (busy), and “c” (connect) as appropriate. “c”
echoes only after the Si2401 detects the Handshake
Tone and the speed synchronization signal is sent. The
signaling is at 300 bps, half-duplex FSK. The host can
Table 13. AT Command Set Extensions
for the Alarm Industry
Command
Function
!1
Dial and switch to DTMF security
mode
!2
Dial and switch to “SIA Format”
X1
SIA half-duplex mode search
X2
SIA half-duplex return online as
transmitter
X3
SIA half-duplex return online as
receiver
相关PDF资料 |
PDF描述 |
|---|---|
| UPA0J272MPD1TD | CAP ALUM 2700UF 6.3V 20% RADIAL |
| UPA0J222MPD1TD | CAP ALUM 2200UF 6.3V 20% RADIAL |
| GBC19DRAS | CONN EDGECARD 38POS R/A .100 SLD |
| CM322522-2R2JL | INDUCTOR CHIP 2.2UH 3225 SMD |
| RR70G821MDN1 | CAP ALUM 820UF 4V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SI2401-FSR | 功能描述:电信线路管理 IC 2400b/s System Side 3rd Gen DAA Tech RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| SI2401URT-EVB | 功能描述:网络开发工具 U 634-SI2401FS10-EVB RoHS:否 制造商:Rabbit Semiconductor 产品:Development Kits 类型:Ethernet to Wi-Fi Bridges 工具用于评估:RCM6600W 数据速率:20 Mbps, 40 Mbps 接口类型:802.11 b/g, Ethernet 工作电源电压:3.3 V |
| SI2403 | 制造商:SILABS 制造商全称:SILABS 功能描述:V.22BIS ISOMODEM CHIPSET WITH ERROR CORRECTION |
| SI2403-FT | 制造商:Silicon Laboratories Inc 功能描述:MODEM CHIP CHIPSET ISOMODEM 2.4KBPS 24TSSOP - Rail/Tube |
| SI2404 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:V.90, V.34, V.32BIS, V.22BIS ISOMODEM?? WITH GLOBAL DAA |
发布紧急采购，3分钟左右您将得到回复。