- 您现在的位置：买卖IC网 > PDF目录16381 > SI2401FS10-EVB (Silicon Laboratories Inc)BOARD EVAL SI2401 UART INTERFACE PDF资料下载
参数资料
| 型号： | SI2401FS10-EVB |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 6/76页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL SI2401 UART INTERFACE |
| 标准包装： | 1 |
| 系列： | ISOmodem® |
| 主要目的： | 电信，调制解调器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | SI2401 |
| 主要属性： | 双路 RJ-11 连接至电话线路，音频连接器 |
| 次要属性： | RS-232，TTL 串行和 USB 接口 |
| 已供物品： | 板，调制解调器，电源 |
| 相关产品： | 336-1095-ND - IC ISOMODEM SYSTEM-SIDE 16SOIC |
| 其它名称： | 336-1167 |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页
Si2401
14
Rev. 1.0
4.2.1. Command/Data Mode
Upon reset, the modem is in command mode and
accepts AT-style commands. An outgoing modem call
can be made using the “ATDT#” (tone dial) or “ATDP#”
(pulse dial) command after the device is configured. If
the handshake is successful, the modem responds with
the “c”, “d”, or “v” string and enters data mode. (The
byte following the “c”, “d”, or “v” is the first data byte.) At
this point, AT-style commands are not accepted. There
are three methods that may be used to return the
Si2401 to command mode:
Use the ESC pin—To program the GPIO3 pin to
function as an ESCAPE input, set GPIO3
SE2[5:4] = 11. In this setting, a positive edge
detected on this pin returns the modem to command
mode. The “ATO” string can be used to reenter data
mode.
Use 9-bit data mode—If 9-bit data format with
escape is programmed, a 1 detected on bit 9 returns
the modem to command mode. (See Figure 2 on
page 9.) This is enabled by setting SE0[3] (ND) = 1
and S15[0] (NBE) = 1. The ATO string can be used
to reenter data mode. Ninth bit escape does not
work in the security modes.
Use “+++”—The escape sequence is a sequence of
three escape characters that are set in S-register
S0F (“+” characters by default). If the ISOmodem
chipset detects the “+++” sequence and detects no
activity on the UART before or after the “+++”
sequence for a time period set by S-register S10, it
returns to command mode. To disable this escape
sequence, set S-register S10 = FF. To remove the
time-dependent behavior, set S-register S10 = 00.
Whether using an escape method or not, when the
carrier is lost, the modem automatically returns to
command mode and reports “N”.
4.2.2. 8-Bit Data Mode (8N1)
The 8-bit data mode is the default mode after powerup
or
reset
and
is
set
by
SE0[3] (ND) = 0b. It is
asynchronous, full duplex, and uses a total of 10 bits
including a start bit (logic 0), eight data bits, and a stop
bit (logic 1). Data received from the remote modem is
transferred from the Si2401 to the host on the RXD pin.
Data transfer to the host begins when the Si2401
asserts a logic 0 start bit on RXD. Data is shifted out of
the Si2401 LSB first at the DTE rate determined by the
SE0[2:0] (SD) setting and terminates with a stop bit.
Data from the host for transmission to the remote
modem is shifted to the Si2401 on TXD beginning with a
start bit, LSB, first at the DTE rate determined by the
SE0[2:0] setting, and terminates with a stop bit.
After the middle of the stop bit time, the Si2401 begins
looking for a logic 1 to logic 0 transition signaling the
start of the next character on TXD to be sent to the line
(remote modem).
4.2.3. 9-Bit Data Mode (9N1)
The 9-bit data mode is set by SE0[3] (ND) = 1. It is
asynchronous, full duplex, and uses a total of 11 bits
including a start bit (logic 0), 9 data bits, and a stop bit
(logic 1). Data received from the line (remote modem) is
transferred from the Si2401 to the host on the RXD pin.
Data transfer to the host begins when the Si2401
asserts a logic 0 start bit on RXD. Data is shifted out of
the Si2401 LSB first at the DTE rate determined by the
SE0[2:0] (SD) setting and terminates with a stop bit.
Data from the host for transmission to the line (remote
modem) is shifted to the Si2401 on TXD beginning with
a start bit, LSB, first at the DTE rate determined by the
S-Register SE0[2:0] (SD) setting, and terminates with a
stop bit. After the middle of the stop bit time, the Si2401
begins looking for a logic 1 to logic 0 transition signaling
the start of the next character on TXD to be sent to the
line (remote modem).
The ninth data bit may be used to indicate an escape by
setting S15[0] (NBE) = 1. In this mode, the ninth data bit
is normally set to 0 when the modem is online. When
the ninth data bit is set to 1, the modem goes offline into
command mode, and the next frame is interpreted as an
AT command. Data mode can be reentered using the
ATO command.
4.2.4. Flow Control
No flow control is needed if the DTE rate and DCE rate
are the same. If the serial link (DTE) data rate is set
higher than the line (DCE) rate of the modem, flow
control is required to prevent loss of data to the
transmitter.
To control data flow, the clear-to-send (CTS) pin is used.
When CTS is asserted, the Si2401 is ready to accept a
character. While CTS is negated, no data should be
sent to the Si2401 on TXD. To simplify flow control, the
Si2401 has an integrated ten character transmit FIFO
and allows for two different CTS reporting methods. By
default, the CTS pin is negated as soon as a start bit is
detected on the TXD pin and remains negated until the
modem is ready to accept another character (see
Figure 2 on page 9.) By setting SFC7[7] = 1 (CTSM),
CTS is negated when the FIFO is 70% full and is
reasserted when the FIFO is 30% full.
相关PDF资料 |
PDF描述 |
|---|---|
| UPA0J272MPD1TD | CAP ALUM 2700UF 6.3V 20% RADIAL |
| UPA0J222MPD1TD | CAP ALUM 2200UF 6.3V 20% RADIAL |
| GBC19DRAS | CONN EDGECARD 38POS R/A .100 SLD |
| CM322522-2R2JL | INDUCTOR CHIP 2.2UH 3225 SMD |
| RR70G821MDN1 | CAP ALUM 820UF 4V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SI2401-FSR | 功能描述:电信线路管理 IC 2400b/s System Side 3rd Gen DAA Tech RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| SI2401URT-EVB | 功能描述:网络开发工具 U 634-SI2401FS10-EVB RoHS:否 制造商:Rabbit Semiconductor 产品:Development Kits 类型:Ethernet to Wi-Fi Bridges 工具用于评估:RCM6600W 数据速率:20 Mbps, 40 Mbps 接口类型:802.11 b/g, Ethernet 工作电源电压:3.3 V |
| SI2403 | 制造商:SILABS 制造商全称:SILABS 功能描述:V.22BIS ISOMODEM CHIPSET WITH ERROR CORRECTION |
| SI2403-FT | 制造商:Silicon Laboratories Inc 功能描述:MODEM CHIP CHIPSET ISOMODEM 2.4KBPS 24TSSOP - Rail/Tube |
| SI2404 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:V.90, V.34, V.32BIS, V.22BIS ISOMODEM?? WITH GLOBAL DAA |
发布紧急采购，3分钟左右您将得到回复。