- 您现在的位置：买卖IC网 > PDF目录68427 > W25Q16DWZPIP (WINBOND ELECTRONICS CORP) 16M X 1 SPI BUS SERIAL EEPROM, PDSO8 PDF资料下载
参数资料
| 型号： | W25Q16DWZPIP |
| 厂商： | WINBOND ELECTRONICS CORP |
| 元件分类： | PROM |
| 英文描述： | 16M X 1 SPI BUS SERIAL EEPROM, PDSO8 |
| 封装： | 6 X 5 MM, GREEN , PLASTIC, WSON-8 |
| 文件页数： | 3/83页 |
| 文件大小： | 1268K |
| 代理商： | W25Q16DWZPIP |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页
W25Q16DW
Publication Release Date: April 01, 2011
- 11 -
Preliminary - Revision A
9.1.3
Quad SPI Instructions
The W25Q16DW supports Quad SPI operation when using instructions such as “Fast Read Quad Output
(6Bh)”, “Fast Read Quad I/O (EBh)”, “Word Read Quad I/O (E7h)” and “Octal Word Read Quad I/O
(E3h)”. These instructions allow data to be transferred to or from the device four to six times the rate of
ordinary Serial Flash. The Quad Read instructions offer a significant improvement in continuous and
random access transfer rates allowing fast code-shadowing to RAM or execution directly from the SPI bus
(XIP). When using Quad SPI instructions the DI and DO pins become bidirectional IO0 and IO1, and the
/WP and /HOLD pins become IO2 and IO3 respectively. Quad SPI instructions require the non-volatile
Quad Enable bit (QE) in Status Register-2 to be set.
9.1.4
QPI Instructions
The W25Q16DW supports Quad Peripheral Interface (QPI) operations only when the device is switched
from Standard/Dual/Quad SPI mode to QPI mode using the “Enable QPI (38h)” instruction. The typical
SPI protocol requires that the byte-long instruction code being shifted into the device only via DI pin in
eight serial clocks. The QPI mode utilizes all four IO pins to input the instruction code, thus only two serial
clocks are required. This can significantly reduce the SPI instruction overhead and improve system
performance in an XIP environment. Standard/Dual/Quad SPI mode and QPI mode are exclusive. Only
one mode can be active at any given time. “Enable QPI (38h)” and “Disable QPI (FFh)” instructions are
used to switch between these two modes. Upon power-up or after a software reset using “Reset (99h)”
instruction, the default state of the device is Standard/Dual/Quad SPI mode. To enable QPI mode, the
non-volatile Quad Enable bit (QE) in Status Register-2 is required to be set. When using QPI instructions,
the DI and DO pins become bidirectional IO0 and IO1, and the /WP and /HOLD pins become IO2 and IO3
respectively. See Figure 3 for the device operation modes.
9.1.5
Hold Function
For Standard SPI and Dual SPI operations, the /HOLD signal allows the W25Q16DW operation to be
paused while it is actively selected (when /CS is low). The /HOLD function may be useful in cases where
the SPI data and clock signals are shared with other devices. For example, consider if the page buffer
was only partially written when a priority interrupt requires use of the SPI bus. In this case the /HOLD
function can save the state of the instruction and the data in the buffer so programming can resume where
it left off once the bus is available again. The /HOLD function is only available for standard SPI and Dual
SPI operation, not during Quad SPI or QPI.
To initiate a /HOLD condition, the device must be selected with /CS low. A /HOLD condition will activate on
the falling edge of the /HOLD signal if the CLK signal is already low. If the CLK is not already low the
/HOLD condition will activate after the next falling edge of CLK. The /HOLD condition will terminate on the
rising edge of the /HOLD signal if the CLK signal is already low. If the CLK is not already low the /HOLD
condition will terminate after the next falling edge of CLK. During a /HOLD condition, the Serial Data
Output (DO) is high impedance, and Serial Data Input (DI) and Serial Clock (CLK) are ignored. The Chip
Select (/CS) signal should be kept active (low) for the full duration of the /HOLD operation to avoid
resetting the internal logic state of the device.
相关PDF资料 |
PDF描述 |
|---|---|
| W25Q20BWUXIP | 2M X 1 SPI BUS SERIAL EEPROM, PDSO8 |
| W25Q32BVSSAG | 32M X 1 SPI BUS SERIAL EEPROM, PDSO8 |
| W25Q32BVSSAP | 32M X 1 SPI BUS SERIAL EEPROM, PDSO8 |
| W25Q32BWSNIP | 4M X 8 SPI BUS SERIAL EEPROM, DSO8 |
| W25Q32BWSSIG | 4M X 8 SPI BUS SERIAL EEPROM, PDSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| W25Q16V | 制造商:WINBOND 制造商全称:Winbond 功能描述:16M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI |
| W25Q16VSFIG | 功能描述:IC FLASH 16MBIT 80MHZ 16SOIC RoHS:是 类别:集成电路 (IC) >> 存储器 系列:SpiFlash® 产品变化通告:Product Discontinuation 26/Apr/2010 标准包装:136 系列:- 格式 - 存储器:RAM 存储器类型:SRAM - 同步，DDR II 存储容量:18M（1M x 18） 速度:200MHz 接口:并联 电源电压:1.7 V ~ 1.9 V 工作温度:0°C ~ 70°C 封装/外壳:165-TBGA 供应商设备封装:165-CABGA（13x15） 包装:托盘 其它名称:71P71804S200BQ |
| W25Q16VSSIG | 功能描述:IC FLASH 16MBIT 80MHZ 8SOIC RoHS:是 类别:集成电路 (IC) >> 存储器 系列:SpiFlash® 产品变化通告:Product Discontinuation 26/Apr/2010 标准包装:136 系列:- 格式 - 存储器:RAM 存储器类型:SRAM - 同步，DDR II 存储容量:18M（1M x 18） 速度:200MHz 接口:并联 电源电压:1.7 V ~ 1.9 V 工作温度:0°C ~ 70°C 封装/外壳:165-TBGA 供应商设备封装:165-CABGA（13x15） 包装:托盘 其它名称:71P71804S200BQ |
| W25Q16VZPIG | 制造商:WINBOND 制造商全称:Winbond 功能描述:16M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI |
| W25Q20BW | 制造商:WINBOND 制造商全称:Winbond 功能描述:1.8V 2M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI |
发布紧急采购，3分钟左右您将得到回复。