- 您现在的位置：买卖IC网 > PDF目录20313 > ADP1048ARQZ-R7 (Analog Devices Inc)IC DGTL PFC CTRLR 24QSOP PDF资料下载
参数资料
| 型号： | ADP1048ARQZ-R7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 33/84页 |
| 文件大小： | 0K |
| 描述： | IC DGTL PFC CTRLR 24QSOP |
| 标准包装： | 1 |
| 模式： | 平均电流 |
| 频率 - 开关： | 30kHz ~ 400kHz |
| 电源电压： | 3 V ~ 3.6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 24-QSOP |
| 包装： | 标准包装 |
| 其它名称： | ADP1048ARQZ-R7DKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页当前第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页
Data Sheet
POWER SUPPLY SYSTEM CALIBRATION AND TRIM
ADP1047/ADP1048
The ADP1047 / ADP1048 allow the entire power supply to be
2.
Adjust the VAC ADC gain trim register (Register 0xFE40)
calibrated and trimmed digitally in the production environ-
ment. The device can calibrate items including the output
voltage, input voltage, input current, and input power, and it
can trim for tolerance errors introduced by sense resistors,
current transformers, and resistor dividers, as well as for its
own internal circuitry.
The part comes factory trimmed at 90% of the input range at a
3.3 V supply, but it can be re-trimmed by the user to compen-
until the VAC value (Register 0x88, READ_VIN) equals
the input voltage reading from a calibrated multimeter.
This step trims for errors in the resistor divider network.
For VAC offset trim, adjust the value in Register 0xFE53.
CURRENT SENSE GAIN AND OFFSET TRIM
The current sense can be calibrated digitally to remove any
errors due to external components.
sate for the errors introduced by external components. With the
exception of the gain and offset trim registers for input power,
the trim registers must be unlocked for write access. To unlock
1.
2.
Apply the maximum load to the output with the low line
input voltage.
To match the input current reading at the maximum
the trim registers, write to the TRIM_PASSWORD register
(Register 0xD6).
OUTPUT VOLTAGE (VFB) CALIBRATION AND TRIM
The voltage sense inputs are optimized for sensing signals at
90% of the input range and cannot sense signals greater than
1.6 V. In a high voltage system, a resistor divider is required to
reduce the high voltage signal to below 1.6 V. It is recommended
that the high voltage signal be reduced to 1 V for best perfor-
mance. The resistor divider can introduce errors, which must be
trimmed out as follows:
nominal input current, adjust the CS ADC gain trim
register until the CS value (Register 0x89, READ_IIN)
equals the measured result of the input current from
calibrated equipment.
If the 500 mV input range is used, adjust Register 0xFE42.
If the 750 mV range is used, adjust Register 0xFE7E.
For CS offset trim, adjust the values in Register 0xFE54 (500 mV
input range) or Register 0xFE7F (750 mV input range).
INPUT POWER GAIN AND OFFSET TRIM
1.
Turn on the power supply with no load attached.
The input power trim has separate trim registers for high line
and low line input.
The output voltage is divided down by the feedback resistor
divider to supply 1 V across the VFB and AGND pins.
1.
Apply the maximum load to the output with the low line
input voltage.
2.
3.
Use a calibrated multimeter to perform the output voltage
reading.
Adjust the VFB ADC gain trim register (Register 0xFE41)
until the power supply outputs the exact value in the
READ_VOUT register (Register 0x8B).
2.
Adjust the power metering gain trim for low line input
register (Register 0xFE34) until the input power value in
the READ_PIN register (Register 0x97) equals the
measured result of the input power from calibrated
equipment.
INPUT VOLTAGE (VAC) GAIN AND OFFSET TRIM
3.
Apply the maximum load to the output with the high line
The input voltage sense point on the power rail requires an
external resistor divider to bring the signal within the operating
input range of the VAC ADC (0 V to 1.6 V). The resistor divider
can introduce errors, which must be trimmed out as follows:
1. Apply the maximum line voltage value to the input of the
power supply.
The VAC resistor divider divides this voltage down at the VAC
pin. The VAC resistor divider is programmed in linear format
input voltage.
4. Adjust the power metering gain trim for high line input
register (Register 0xFE8F) until the input power value in
the READ_PIN register (Register 0x97) equals the
measured result of the input power from the calibrated
equipment.
For input power offset trim, adjust the values in Register 0xFE33
(for low line input) and Register 0xFE8E (for high line input).
using the VIN scale monitor register (Register 0xFE3B).
Rev. 0 | Page 33 of 84
相关PDF资料 |
PDF描述 |
|---|---|
| RCB06DHRD | CONN CARD EXTEND 12POS .050" |
| V72A5C300B | CONVERTER MOD DC/DC 5V 300W |
| 395-120-520-801 | CARD EDGE 120PS DL .100X.200 BLK |
| T97R686K025LSA | CAP TANT 68UF 25V 10% 2824 |
| 345-120-540-202 | CARDEDGE 120POS DUAL .100 GREEN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADP1048DC1-EVALZ | 功能描述:DAUGHTERCARD ADP1048 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081 |
| ADP1048WARQZ-R7 | 功能描述:PFC IC Average Current 30kHz ~ 400kHz 24-QSOP 制造商:analog devices inc. 系列:- 包装:带卷（TR） 零件状态:有效 模式:平均电流 频率 - 开关:30kHz ~ 400kHz 电流 - 启动:- 电压 - 电源:3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:24-SSOP（0.209"，5.30mm 宽） 供应商器件封装:24-QSOP 标准包装:1,000 |
| ADP1050ACPZ-R7 | 功能描述:Power Supply Controller Power Supply Controller/Monitor 20-LFCSP-WQ (4x4) 制造商:analog devices inc. 系列:- 包装:剪切带（CT） 零件状态:有效 应用:电源控制器/监控器 电压 - 输入:0 V ~ 1.6 V 电压 - 电源:3 V ~ 3.6 V 电流 - 电源:28.5mA 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:20-WFQFN 裸露焊盘，CSP 供应商器件封装:20-LFCSP-WQ（4x4） 标准包装:1 |
| ADP1050ACPZ-RL | 功能描述:Power Supply Controller Power Supply Controller/Monitor 20-LFCSP-WQ (4x4) 制造商:analog devices inc. 系列:- 包装:带卷（TR） 零件状态:在售 应用:电源控制器/监控器 电压 - 输入:0 V ~ 1.6 V 电压 - 电源:3 V ~ 3.6 V 电流 - 电源:28.5mA 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:20-WFQFN 裸露焊盘，CSP 供应商器件封装:20-LFCSP-WQ（4x4） 标准包装:5,000 |
| ADP1050DC1-EVALZ | 功能描述:ADP1050 - Power Management, Digital Power Controller Evaluation Board 制造商:analog devices inc. 系列:- 零件状态:有效 主要用途:电源管理，数字电源控制器 嵌入式:- 使用的 IC/零件:ADP1050 主要属性:- 辅助属性:- 所含物品:板 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。