- 您现在的位置：买卖IC网 > PDF目录20313 > ADP1048ARQZ-R7 (Analog Devices Inc)IC DGTL PFC CTRLR 24QSOP PDF资料下载
参数资料
| 型号： | ADP1048ARQZ-R7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 39/84页 |
| 文件大小： | 0K |
| 描述： | IC DGTL PFC CTRLR 24QSOP |
| 标准包装： | 1 |
| 模式： | 平均电流 |
| 频率 - 开关： | 30kHz ~ 400kHz |
| 电源电压： | 3 V ~ 3.6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 24-QSOP |
| 包装： | 标准包装 |
| 其它名称： | ADP1048ARQZ-R7DKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页当前第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页
Data Sheet
WRITE OPERATION (BYTE WRITE AND BLOCK
WRITE)
Before performing a write to Page 2 through Page 15 of the
main block, the user must first unlock the EEPROM (see the
Write to Page 0 and Page 1
Page 0 and Page 1 of the main block are reserved for storing the
default settings and user settings, respectively. The user cannot
perform a direct write operation to Page 0 or Page 1 using the
EEPROM_DATA_xx commands. If the user writes to Page 0,
Page 1 returns a no acknowledge. To program the register con-
tents of Page 1 of the main block, it is recommended that the
STORE_USER_ALL command be used (Command Code 0x15).
See the Save Register Settings to the User Scratch Pad section.
Write to Page 2 Through Page 15
The data in the EEPROM main block can be programmed
(written to) one byte at a time or in multiple bytes in series using
the EEPROM_DATA_xx commands (Command Code 0xB0 to
Command Code 0xBF). Before executing this command, the
user can program the offset from the page boundary where
the first byte is written using the EEPROM_ADDR_OFFSET
command (Register 0xD3).
If the targeted page has not yet been erased, the user can erase
In the following example, four bytes are written to Page 9,
starting from the 256 th byte of that page.
ADP1047/ADP1048
On power-up, Page 0 and Page 1 are also protected from read
access, and the EEPROM must first be unlocked to read these
pages.
Unlock EEPROM
To unlock the EEPROM, perform two consecutive writes with
the correct password (default = 0xFF) using the EEPROM_
PASSWORD command (Register 0xD5). The EEPROM_
UNLOCKED flag (Bit 6 of Register 0xFE81) is set to indicate
that the EEPROM is unlocked for write access.
Lock EEPROM
To lock the EEPROM, write any byte other than the correct
password using the EEPROM_PASSWORD command
(Register 0xD5). The EEPROM unlock flag is cleared to
indicate that the EEPROM is locked from write access.
Change EEPROM Password
To change the EEPROM password, the EEPROM must first be
unlocked. To change the EEPROM password, first write the
correct password using the EEPROM_PASSWORD command
(Register 0xD5). Immediately write the new password using the
EEPROM_PASSWORD command. The password is now
changed to the new password.
DOWNLOADING EEPROM SETTINGS TO INTERNAL
REGISTERS
Download User Settings to Registers
The user settings are stored in Page 1 of the EEPROM main
block. These settings are downloaded from the EEPROM into
the registers under the following conditions:
1.
Set address offset = 256.
?
On power-up. The user settings are automatically down-
W
S
SLAVE
ADDRESS
MASTER TO SLAVE
SLAVE TO MASTER
A
0xD3
A
0x01
A
0x00
A
P
?
loaded into the internal registers, powering the part up in
a state previously saved by the user.
On execution of the RESTORE_USER_ALL command
2.
Write four bytes to Page 9.
(Command Code 0x16). This command allows the user
to force a download of the user settings from the EEPROM
S
SLAVE
ADDRESS
W
A
0xB9
A
BYTE COUNT =
4
A
main block, Page 1, into the internal registers.
DATA BYTE 1
A
...
DATA BYTE 4
A
P
Download Factory Settings to Registers
The factory default settings are stored in Page 0 of the EEPROM
MASTER TO SLAVE
SLAVE TO MASTER
Note that the block write command can write a maximum of
256 bytes for any single transaction.
EEPROM PASSWORD
main block. The factory settings can be downloaded from the
EEPROM into the internal registers using the RESTORE_
DEFAULT_ALL command (Command Code 0x12).
When this command is executed, the EEPROM password is also
reset to the factory default setting of 0xFF.
On power-up, the EEPROM is locked and protected from
accidental writes or erases. Only reads from Page 2 to Page 15
are allowed when the EEPROM is locked. Before any data can
be written (programmed) to the EEPROM, the EEPROM must
be unlocked for write access. After it is unlocked, the EEPROM
is opened for reading, writing, and erasing.
Rev. 0 | Page 39 of 84
相关PDF资料 |
PDF描述 |
|---|---|
| RCB06DHRD | CONN CARD EXTEND 12POS .050" |
| V72A5C300B | CONVERTER MOD DC/DC 5V 300W |
| 395-120-520-801 | CARD EDGE 120PS DL .100X.200 BLK |
| T97R686K025LSA | CAP TANT 68UF 25V 10% 2824 |
| 345-120-540-202 | CARDEDGE 120POS DUAL .100 GREEN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADP1048DC1-EVALZ | 功能描述:DAUGHTERCARD ADP1048 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081 |
| ADP1048WARQZ-R7 | 功能描述:PFC IC Average Current 30kHz ~ 400kHz 24-QSOP 制造商:analog devices inc. 系列:- 包装:带卷（TR） 零件状态:有效 模式:平均电流 频率 - 开关:30kHz ~ 400kHz 电流 - 启动:- 电压 - 电源:3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:24-SSOP（0.209"，5.30mm 宽） 供应商器件封装:24-QSOP 标准包装:1,000 |
| ADP1050ACPZ-R7 | 功能描述:Power Supply Controller Power Supply Controller/Monitor 20-LFCSP-WQ (4x4) 制造商:analog devices inc. 系列:- 包装:剪切带（CT） 零件状态:有效 应用:电源控制器/监控器 电压 - 输入:0 V ~ 1.6 V 电压 - 电源:3 V ~ 3.6 V 电流 - 电源:28.5mA 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:20-WFQFN 裸露焊盘，CSP 供应商器件封装:20-LFCSP-WQ（4x4） 标准包装:1 |
| ADP1050ACPZ-RL | 功能描述:Power Supply Controller Power Supply Controller/Monitor 20-LFCSP-WQ (4x4) 制造商:analog devices inc. 系列:- 包装:带卷（TR） 零件状态:在售 应用:电源控制器/监控器 电压 - 输入:0 V ~ 1.6 V 电压 - 电源:3 V ~ 3.6 V 电流 - 电源:28.5mA 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:20-WFQFN 裸露焊盘，CSP 供应商器件封装:20-LFCSP-WQ（4x4） 标准包装:5,000 |
| ADP1050DC1-EVALZ | 功能描述:ADP1050 - Power Management, Digital Power Controller Evaluation Board 制造商:analog devices inc. 系列:- 零件状态:有效 主要用途:电源管理，数字电源控制器 嵌入式:- 使用的 IC/零件:ADP1050 主要属性:- 辅助属性:- 所含物品:板 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。