参数资料
| 型号： | ATMEGA103-6AI |
| 厂商： | Atmel |
| 文件页数： | 24/141页 |
| 文件大小： | 0K |
| 描述： | IC MCU 128K 6MHZ A/D IT 64TQFP |
| 产品培训模块： | megaAVR Introduction |
| 标准包装： | 90 |
| 系列： | AVR® ATmega |
| 核心处理器： | AVR |
| 芯体尺寸： | 8-位 |
| 速度： | 6MHz |
| 连通性： | SPI，UART/USART |
| 外围设备： | POR，PWM，WDT |
| 输入/输出数： | 32 |
| 程序存储器容量： | 128KB（64K x 16） |
| 程序存储器类型： | 闪存 |
| EEPROM 大小： | 4K x 8 |
| RAM 容量： | 4K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 4 V ~ 5.5 V |
| 数据转换器： | A/D 8x10b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 64-TQFP |
| 包装： | 托盘 |
| 配用： | ATSTK501-ND - ADAPTER KIT FOR 64PIN AVR MCU |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页
12
ATmega103(L)
0945I–AVR–02/07
The 4096 first Data memory locations address both the Register File, the I/O memory
and the internal Data SRAM. The first 96 locations address the Register File and I/O
memory, and the next 4000 locations address the internal Data SRAM.
An optional external Data SRAM can be used with the ATmega103(L). This SRAM will
occupy an area in the remaining address locations in the 64K address space. This area
starts at the address following the internal SRAM. If a 64K external SRAM is used, 4K of
the external memory is lost as the addresses are occupied by internal memory.
When the addresses accessing the SRAM memory space exceeds the internal Data
memory locations, the external Data SRAM is accessed using the same instructions as
for the internal Data memory access. When the internal Data memories are accessed,
the read and write strobe pins (RD and WR) are inactive during the whole access cycle.
External SRAM operation is enabled by setting the SRE bit in the MCUCR Register.
Accessing external SRAM takes one additional clock cycle per byte compared to access
of the internal SRAM. This means that the commands LD, ST, LDS, STS, PUSH and
POP take one additional clock cycle. If the Stack is placed in external SRAM, interrupts,
subroutine calls and returns take two clock cycles extra because the 2-byte Program
Counter is pushed and popped. When external SRAM interface is used with wait state,
two additional clock cycles are used per byte. This has the following effect: Data transfer
instructions take two extra clock cycles, whereas interrupt, subroutine calls and returns
will need four clock cycles more than specified in the “Instruction Set Summary” on page
The five different addressing modes for the Data memory cover: Direct, Indirect with
Displacement, Indirect, Indirect with Pre-decrement and Indirect with Post-increment. In
the Register File, registers R26 to R31 feature the indirect addressing pointer registers.
The Indirect with Displacement mode features 63 address locations reached from the
base address given by the Y- or Z-register.
When using register indirect addressing modes with automatic Pre-decrement and Post-
increment, the address registers X, Y, and Z are decremented and incremented.
The entire Data address space including the 32 general purpose working registers and
the 64 I/O Registers are all accessible through all these addressing modes. See the
next section for a detailed description of the different addressing modes.
Program and Data
Addressing Modes
The ATmega103(L) AVR RISC microcontroller supports powerful and efficient address-
ing modes for access to the Program memory (Flash) and Data memory (SRAM,
Register File and I/O memory). This section describes the different addressing modes
supported by the AVR architecture. In the figures, OP means the operation code part of
the instruction word. To simplify, not all figures show the exact location of the address-
ing bits.
相关PDF资料 |
PDF描述 |
|---|---|
| ATMEGA128A-AUR | MCU AVR 128K FLASH 16MHZ 64TQFP |
| ATMEGA128L-8MJ | IC MCU AVR 128K 8MHZ LV 64-QFN |
| ATMEGA16-16MUR | MCU AVR 16KB FLASH 16MHZ 44QFN |
| ATMEGA164PA-AN | IC MCU AVR 16K FLASH 44TQFP |
| ATMEGA164PA-CUR | MCU AVR 16KB FLASH 20MHZ 49VFBGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ATMEGA103L | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-bit Microcontroller with 128K Bytes In-System Programmable Flash |
| ATMEGA103L-4AC | 功能描述:8位微控制器 -MCU TQFP-64 128K FLASH 3 RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| ATMEGA103L-4AI | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-Bit Microcontroller with 64K/128K Bytes In-System Programmable Flash |
| ATMEGA128 | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-bit Microcontroller with 128K Bytes In-System Programmable Flash |
| ATMEGA128(L) | 制造商:未知厂家 制造商全称:未知厂家 功能描述:ATmega128(L) Preliminary Summary [Updated 9/03. 23 Pages] |
发布紧急采购，3分钟左右您将得到回复。