参数资料
| 型号： | DS3106LN+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 32/92页 |
| 文件大小： | 0K |
| 描述： | IC TIMING LINE CARD 64-LQFP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 160 |
| 类型： | 定时卡 IC，多路复用器 |
| PLL： | 是 |
| 主要目的： | 以太网，SONET/SDH，Stratum，电信 |
| 输入： | CMOS，TTL |
| 输出： | CMOS，LVDS，LVPECL，TTL |
| 电路数： | 1 |
| 比率 - 输入:输出： | 2:2 |
| 差分 - 输入:输出： | 无/是 |
| 频率 - 最大： | 312.5MHz |
| 电源电压： | 1.62 V ~ 1.98 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-LQFP |
| 供应商设备封装： | 64-LQFP（10x10） |
| 包装： | 托盘 |
| 产品目录页面： | 1429 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页当前第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页
DS3106
38
8. Register Descriptions
The DS3106 has an overall address range from 000h to 1FFh. Table 8-1 in Section 8.4 shows the register map. In
each register, bit 7 is the MSB and bit 0 is the LSB. Register addresses not listed and bits marked “—“ are reserved
and must be written with 0. Writing other values to these registers may put the device in a factory test mode
resulting in undefined operation. Bits labeled “0” or “1” must be written with that value for proper operation. Register
fields with underlined names are read-only fields; writes to these fields have no effect. All other fields are read-
write. Register fields are described in detail in the register descriptions that follow Table 8-1.
Note: Systems must be able to access the entire address range from 0 to 01FFh. Proper device initialization
requires a sequence of writes to addresses in the range 0180-01FFh.
8.1
Status Bits
The device has two types of status bits. Real-time status bits are read-only and indicate the state of a signal at the
time it is read. Latched status bits are set when a signal changes state (low-to-high, high-to-low, or both, depending
on the bit) and cleared when written with a logic 1 value. Writing a 0 has no effect. When set, some latched status
bits can cause an interrupt request on the INTREQ pin if enabled to do so by corresponding interrupt enable bits.
ISR#.LOCK# are special-case latched status bits because they cannot create an interrupt request on the INTREQ
pin and a “write 0” is needed to clear them.
8.2
Configuration Fields
Configuration fields are read-write. During reset, each configuration field reverts to the default value shown in the
register definition. Configuration register bits marked “—” are reserved and must be written with 0.
8.3
Multiregister Fields
Multiregister fields—such as FREQ[18:0] in registers FREQ1, FREQ2, and FREQ3—must be handled carefully to
ensure that the bytes of the field remain consistent. A write access to a multiregister field is accomplished by
writing all the registers of the field in any order, with no other accesses to the device in between. If the write
sequence is interrupted by another access, none of the bytes are written and the MSR4:MRAA latched status bit is
set to indicate the write was aborted. A read access from a multiregister field is accomplished by reading the
registers of the field in any order, with no other accesses to the device in between. When one register of a
multiregister field is read, the other register(s) in the field are frozen until after they are all read. If the read
sequence is interrupted by another access, the registers of the multibyte field are unfrozen and the MSR4:MRAA
bit is set to indicate the read was aborted. For best results, interrupt servicing should be disabled in the
microprocessor before a multiregister access and then enabled again after the access is complete. The
multiregister fields are:
FIELD
REGISTERS
ADDRESSES
TYPE
FREQ[18:0]
0Ch, 0Dh, 07h
Read Only
MCLKFREQ[15:0]
3Ch, 3Dh
Read/Write
HARDLIM[9:0]
41h, 42h
Read/Write
DIVN[15:0]
46h, 47h
Read/Write
PHASE[15:0]
77h, 78h
Read Only
相关PDF资料 |
PDF描述 |
|---|---|
| DS3231MZ+ | IC RTC I2C 8SOIC |
| DS3231SN#T&R | IC RTC W/TCXO 16-SOIC |
| DS3232MZ+ | IC RTC W/SRAM I2C 8SOIC |
| DS3232SN#T&R | IC RTC W/TCXO 20-SOIC |
| DS3234S# | IC RTC W/TCXO 20-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS3106LN+ | 功能描述:计时器和支持产品 Line Card Timing IC RoHS:否 制造商:Micrel 类型:Standard 封装 / 箱体:SOT-23 内部定时器数量:1 电源电压-最大:18 V 电源电压-最小:2.7 V 最大功率耗散: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Reel |
| DS3107FP000 | 制造商:Thomas & Betts 功能描述:30A,CON,2P3W,MG,107,125V |
| DS3107FRAB0 | 制造商:Thomas & Betts 功能描述:30A,REC,2P3W,MG,107,AB0,125,SC |
| DS3107MP000 | 制造商:Thomas & Betts 功能描述:30A,PLG,2P3W,MG,107,125V |
| DS3107MP00K | 制造商:Thomas & Betts 功能描述:30A,PLG,2P3W,MG,107,125V,CC |
发布紧急采购，3分钟左右您将得到回复。