收藏本站
参数资料
型号： DSPB56364AF100
厂商： Freescale Semiconductor
文件页数： 24/148页
文件大小： 0K
描述： IC DSP 24BIT AUD 100MHZ 100-LQFP
标准包装： 90
系列： DSP56K/Symphony
类型： 音频处理器
接口： 主机接口，I²C，SAI，SPI
时钟速率： 100MHz
非易失内存： ROM（24 kB）
芯片上RAM： 11.25kB
电压 - 输入/输出： 3.30V
电压 - 核心： 3.30V
工作温度： -40°C ~ 105°C
安装类型： 表面贴装
封装/外壳： 100-LQFP
供应商设备封装： 100-LQFP（14x14）
包装： 托盘
Serial Host Interface
DSP56364 Technical Data, Rev. 4.1
2-8
Freescale Semiconductor
HA0
Input
Tri-stated
I2C Slave Address 0—This signal uses a Schmitt-trigger input when configured for the
I2C mode. When configured for I2C slave mode, the HA0 signal is used to form the
slave device address. HA0 is ignored when configured for the I2C master mode.
This signal is tri-stated during hardware, software, and individual reset. Thus, there is
no need for an external pull-up in this state.
This input is 5 V tolerant.
SS
Input
SPI Slave Select—This signal is an active low Schmitt-trigger input when configured
for the SPI mode. When configured for the SPI Slave mode, this signal is used to enable
the SPI slave for transfer. When configured for the SPI master mode, this signal should
be kept deasserted (pulled high). If it is asserted while configured as SPI master, a bus
error condition is flagged. If SS is deasserted, the SHI ignores SCK clocks and keeps
the MISO output signal in the high-impedance state.
HA2
Input
I2C Slave Address 2—This signal uses a Schmitt-trigger input when configured for the
I2C mode. When configured for the I2C Slave mode, the HA2 signal is used to form the
slave device address. HA2 is ignored in the I2C master mode.
This signal is tri-stated during hardware, software, and individual reset. Thus, there is
no need for an external pull-up in this state.
This input is 5 V tolerant.
HREQ
Input or
Output
Tri-stated
Host Request—This signal is an active low Schmitt-trigger input when configured for
the master mode but an active low output when configured for the slave mode.
When configured for the slave mode, HREQ is asserted to indicate that the SHI is ready
for the next data word transfer and deasserted at the first clock pulse of the new data
word transfer. When configured for the master mode, HREQ is an input. When asserted
by the external slave device, it will trigger the start of the data word transfer by the
master. After finishing the data word transfer, the master will await the next assertion of
HREQ to proceed to the next transfer.
This signal is tri-stated during hardware, software, personal reset, or when the
HREQ1–HREQ0 bits in the HCSR are cleared. There is no need for external pull-up in
this state.
This input is 5 V tolerant.
Table 2-9 Serial Host Interface Signals (continued)
Signal
Name
Signal
Type
State During
Reset
Signal Description
相关PDF资料
PDF描述
DSPB56366AG120 IC DSP 24BIT AUD 120MHZ 144-LQFP
DSPB56367AG150 IC DSP 24BIT 150MHZ 144-LQFP
DSPB56371AF180 IC DSP 24BIT 180MHZ 80-LQFP
DSPB56374AEC IC DSP 24BIT 150MHZ 52-LQFP
DSPB56720CAG DSP 24BIT AUD 200MHZ 144-LQFP
相关代理商/技术参数
参数描述
DSPB56364FU100 制造商:Rochester Electronics LLC 功能描述:24 BIT AUDIO DSP - Bulk 制造商:Motorola Inc 功能描述: 制造商:MOTOROLA 功能描述:
DSPB56364FU100R2 制造商:Freescale Semiconductor 功能描述:DSP FIX PT 24BIT 100MHZ 100MIPS 100LQFP - Tape and Reel
DSPB56366AG120 功能描述:数字信号处理器和控制器 - DSP, DSC LEAD FREE DSPB56366 RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
DSPB56366PV120 制造商:Motorola Inc 功能描述: 制造商:Freescale Semiconductor 功能描述:IC 制造商:MOTOROLA 功能描述:
DSPB56367AG150 功能描述:数字信号处理器和控制器 - DSP, DSC 150Mhz/150MIPS RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*