- 您现在的位置：买卖IC网 > PDF目录1917 > DSPB56367AG150 (Freescale Semiconductor)IC DSP 24BIT 150MHZ 144-LQFP PDF资料下载
参数资料
| 型号： | DSPB56367AG150 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 88/100页 |
| 文件大小： | 0K |
| 描述： | IC DSP 24BIT 150MHZ 144-LQFP |
| 标准包装： | 60 |
| 系列： | DSP56K/Symphony |
| 类型： | 音频处理器 |
| 接口： | 主机接口，I²C，SAI，SPI |
| 时钟速率： | 150MHz |
| 非易失内存： | ROM（240 kB） |
| 芯片上RAM： | 69kB |
| 电压 - 输入/输出： | 3.30V |
| 电压 - 核心： | 1.80V |
| 工作温度： | -40°C ~ 95°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 144-LQFP |
| 供应商设备封装： | 144-LQFP（20x20） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页当前第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页
Electrical Design Considerations
DSP56367 Technical Data, Rev. 2.1
5-2
Freescale Semiconductor
To minimize temperature variation across the surface, the thermal resistance is measured from the
junction to the outside surface of the package (case) closest to the chip mounting area when that
surface has a proper heat sink.
To define a value approximately equal to a junction-to-board thermal resistance, the thermal
resistance is measured from the junction to where the leads are attached to the case.
If the temperature of the package case (TT) is determined by a thermocouple, the thermal resistance
is computed using the value obtained by the equation: (TJ – TT)/PD.
As noted above, the junction-to-case thermal resistances quoted in this data sheet are determined using the
first definition. From a practical standpoint, that value is also suitable for determining the junction
temperature from a case thermocouple reading in forced convection environments. In natural convection,
using the junction-to-case thermal resistance to estimate junction temperature from a thermocouple
reading on the case of the package will estimate a junction temperature slightly hotter than actual
temperature. Hence, the new thermal metric, thermal characterization parameter or
Ψ
JT, has been defined
to be (TJ – TT)/PD. This value gives a better estimate of the junction temperature in natural convection
when using the surface temperature of the package. Remember that surface temperature readings of
packages are subject to significant errors caused by inadequate attachment of the sensor to the surface and
to errors caused by heat loss to the sensor. The recommended technique is to attach a 40-gauge
thermocouple wire and bead to the top center of the package with thermally conductive epoxy.
5.2
Electrical Design Considerations
CAUTION
This device contains circuitry protecting against damage due to high static
voltage or electrical fields. However, normal precautions should be taken to
avoid exceeding maximum voltage ratings. Reliability of operation is
enhanced if unused inputs are tied to an appropriate logic voltage level (e.g.,
either GND or VCC). The suggested value for a pull-up or pull-down resistor
is 10 k ohm.
Use the following list of recommendations to assure correct DSP operation:
Provide a low-impedance path from the board power supply to each VCC pin on the DSP and from
the board ground to each GND pin.
Use at least six 0.01–0.1
F bypass capacitors positioned as close as possible to the four sides of
the package to connect the VCC power source to GND.
Ensure that capacitor leads and associated printed circuit traces that connect to the chip VCC and
GND pins are less than 1.2 cm (0.5 inch) per capacitor lead.
Use at least a four-layer PCB with two inner layers for VCC and GND.
Because the DSP output signals have fast rise and fall times, PCB trace lengths should be minimal.
This recommendation particularly applies to the address and data buses as well as the IRQA,
IRQB, IRQD, and TA pins. Maximum PCB trace lengths on the order of 15 cm (6 inches) are
recommended.
相关PDF资料 |
PDF描述 |
|---|---|
| DSPB56371AF180 | IC DSP 24BIT 180MHZ 80-LQFP |
| DSPB56374AEC | IC DSP 24BIT 150MHZ 52-LQFP |
| DSPB56720CAG | DSP 24BIT AUD 200MHZ 144-LQFP |
| DSPB56724AG | DSP 24BIT AUD 250MHZ 144-LQFP |
| DSPIC30F2010T-20E/MM | IC DSPIC MCU/DSP 12K 28QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DSPB56367PV150 | 功能描述:数字信号处理器和控制器 - DSP, DSC 150Mhz/ 150MIPS RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT |
| DSPB5636AG120 | 制造商:Freescale Semiconductor 功能描述: |
| DSPB56371AF150 | 功能描述:数字信号处理器和控制器 - DSP, DSC 150 MHZ VERSION DSPB371 RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT |
| DSPB56371AF180 | 功能描述:数字信号处理器和控制器 - DSP, DSC BLANK ROM VERSION 56371 RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT |
| DSPB56371AF180 | 制造商:Freescale Semiconductor 功能描述:Digital Signal Processor (DSP) IC |
发布紧急采购，3分钟左右您将得到回复。