- 您现在的位置：买卖IC网 > PDF目录18822 > HSP50210JC-52Z (Intersil)IC DEMODULATOR COSTAS 84-PLCC PDF资料下载
参数资料
| 型号： | HSP50210JC-52Z |
| 厂商： | Intersil |
| 文件页数： | 35/51页 |
| 文件大小： | 0K |
| 描述： | IC DEMODULATOR COSTAS 84-PLCC |
| 标准包装： | 15 |
| 功能： | 解调器 |
| 频率： | 52MHz |
| RF 型： | AM，FM |
| 封装/外壳： | 84-LCC（J 形引线） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页当前第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页
HSP50210
TABLE 21. CARRIER LOOP FILTER CONTROL REGISTER #1 (Continued)
DESTINATION ADDRESS = 6
BIT
POSITION
5
4-0
FUNCTION
Lead/Lag to Internal
NCO Routing
Error Accumulation
DESCRIPTION
0 = Sum of lead and lag paths routed to the internal NCO. (32 MSBs of sum are routed).
1 = The lead term is routed to the internal NCO. (32 MSBs of lead term are routed).
These bits set the number of phase and frequency error measurements that are accumulated before the
Carrier and AFC Loop Filters are run. Since the Loop Filters can only accept new inputs every 6 CLKs
(normally at the symbol rate), the error accumulation is required to ensure that no phase or frequency
error outputs are missed when error terms are generated at a rate greater than 1/6 CLK (see “Carrier
Phase Error Detector” on page 18). The 5-bit value programmed here should be set to one less than the
desired number of error terms to accumulate. For example, setting these bits to 0011 (BINARY) would
cause 4 error terms to be accumulated. A total range from 1 to 32 is provided.
When error accumulation is used, divide the Lead Gain by the number of errors accumulated. Note that
the LAG Gain does not need to be scaled since it increases to compensate for the delay, since it is an
accumulator.
TABLE 22. CARRIER LOOP FILTER CONTROL REGISTER #2
DESTINATION ADDRESS = 7
BIT
POSITION
31-8
7-6
5
4
3
2
1
0
FUNCTION
Not Used
Reserved
Lead Phase Error
Enable
Lag Phase Error
Enable
AFC Enable
Carrier Sweep Enable
Invert Carrier Phase
Error
Invert Carrier
Frequency Error
DESCRIPTION
No programming required.
Reserved. Set to 0 for proper operation.
0 = Carrier Phase Error enabled to lead processing path of loop filter.
1 = Carrier Phase Error to lead processing path of loop filter zeroed.
0 = Carrier Phase Error enabled to lag processing path of loop filter.
1 = Carrier Phase Error to lag processing path of loop filter zeroed (First Order Loop).
0 = Frequency error enabled to lag processing path of Carrier Loop Filter.
1 = Frequency error zeroed.
0 = Frequency sweep input to the lag path of the Carrier Loop Filter enabled.
1 = Sweep input to Carrier Loop Filter zeroed.
0 = Carrier Phase Error is normal into Carrier Loop Filter.
1 = Carrier Phase Error is inverted into Carrier Loop Filter.
0 = Carrier Frequency Error is normal into AFC loop filter.
1 = Carrier Frequency Error is inverted into AFC Loop filter.
TABLE 23. CARRIER LOOP FILTER UPPER LIMIT CONTROL REGISTER
DESTINATION ADDRESS = 8
BIT
POSITION
31-0
FUNCTION
Carrier Loop Filter
Upper limit
DESCRIPTION
The 32-bit two’s complement value programmed here sets the upper sweep and tracking limit of the Carrier
Loop Filter by setting the upper limit of the loop filter’s lag accumulator. If the limit is exceeded, the upper 32
bits of the 40-bit accumulator are set to the limit, and the 8 LSBs are set to zero.
TABLE 24. CARRIER LOOP FILTER LOWER LIMIT CONTROL REGISTER
DESTINATION ADDRESS = 9
BIT
POSITION
31-0
FUNCTION
Carrier Loop Filter
Lower limit
35
DESCRIPTION
The 32-bit two’s complement value programmed here sets the Lower sweep and tracking limit of the Carrier
Loop Filter by setting the lower limit of the loop filter’s lag accumulator. If the running sum falls below the limit,
the upper 32 bits of the 40-bit accumulator are set to the limit, and the 8 LSBs are set to zero.
FN3652.5
July 2, 2008
相关PDF资料 |
PDF描述 |
|---|---|
| HMR2300-D20-485 | MAGNETOMETER RS485 W/CASE |
| PT080-60-0 | CORD PATCH PIN TIP PLUG 60" BLK |
| ISL5829/2INZ | IC DAC 12BIT CMOS DUAL 48LQFP |
| HMR2300-D00-485 | MAGNETOMETER RS485 |
| PT080-48-2 | CORD PATCH PIN TIP PLUG 48" RED |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HSP50210JI-52 | 功能描述:上下转换器 COSTAS DEMODULATOR,84 PLCC,52MHZ,IND RoHS:否 制造商:Texas Instruments 产品:Down Converters 射频:52 MHz to 78 MHz 中频:300 MHz LO频率: 功率增益: P1dB: 工作电源电压:1.8 V, 3.3 V 工作电源电流:120 mA 最大功率耗散:1 W 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PQFP-128 |
| HSP50210JI-52Z | 功能描述:上下转换器 COSTAS DEMODULATOR 84 PLCC 52MHZ IND RoHS:否 制造商:Texas Instruments 产品:Down Converters 射频:52 MHz to 78 MHz 中频:300 MHz LO频率: 功率增益: P1dB: 工作电源电压:1.8 V, 3.3 V 工作电源电流:120 mA 最大功率耗散:1 W 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PQFP-128 |
| HSP50214 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Programmable Downconverter |
| HSP50214A | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Programmable Downconverter |
| HSP50214AVC | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
发布紧急采购，3分钟左右您将得到回复。