参数资料
型号: I5104XY
厂商: WINBOND ELECTRONICS CORP
元件分类: 音频合成
英文描述: 262.2 SEC, SPEECH SYNTHESIZER WITH RCDG, UUC25
封装: DIE-25
文件页数: 76/87页
文件大小: 616K
代理商: I5104XY
79
8393B-MCU Wireless-02/13
ATmega256/128/64RFR2
can be associated with an expected packet error rate. The PER is the ratio of erroneous
received frames to the total number of received frames. A PER of zero indicates no
frame error whereas at a PER of one no frame was received correctly.
The radio transceiver uses correlation results of multiple symbols within a frame to
determine the LQI value. This is done for each received frame. The minimum frame
length for a valid LQI value is two octets PSDU. LQI values are integers ranging from 0
to 255.
The following figure shows an example of a conditional packet error rate when receiving
a certain LQI value.
Figure 9-20. Conditional Packet Error Rate versus LQI
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
0
50
100
150
200
250
P
E
R
LQI
The values are taken from received frames of PSDU length of 20 octets on
transmission channels with reasonable low multipath delay spreads. If the transmission
channel characteristic has a higher multipath delay spread than assumed in the
example, the PER is slightly higher for a certain LQI value. Since the packet error rate
is a statistical value, the PER shown in Figure 9-20 above is based on a huge number
of transactions. A reliable estimation of the packet error rate cannot be based on a
single or a small number of LQI values.
9.5.6.2 Request a LQI Measurement
The LQI byte can be obtained after a frame has been received by the radio transceiver.
One additional byte is automatically attached to the received frame containing the LQI
value. This information can also be read via Frame Buffer read access, see "User
accessible Frame Content" on page 84. The LQI byte can be read after the
TRX24_RX_END interrupt.
9.5.6.3 Data Interpretation
According to IEEE 802.15.4 a low LQI value is associated with low signal strength
and/or high signal distortions. Signal distortions are mainly caused by interference
signals and/or multipath propagation. High LQI values indicate a sufficient high signal
power and low signal distortions.
相关PDF资料
PDF描述
IA3-1206WA00D5 0 MHz - 18000 MHz RF/MICROWAVE FIXED ATTENUATOR
IA3-0706SS58D0 0 MHz - 18000 MHz RF/MICROWAVE FIXED ATTENUATOR
IA3-2010SG30D0 0 MHz - 18000 MHz RF/MICROWAVE FIXED ATTENUATOR
IAC-0706SG04D0 0 MHz - 18000 MHz RF/MICROWAVE FIXED ATTENUATOR
IAC-0706SS22D0 0 MHz - 18000 MHz RF/MICROWAVE FIXED ATTENUATOR
相关代理商/技术参数
参数描述
I5108E 制造商:WINBOND 制造商全称:Winbond 功能描述:SINGLE-CHIP 1 TO 16 MINUTES DURATION VOICE RECORD/PLAYBACK DEVICES WITH DIGITAL STORAGE CAPABILITY
I5108EI 制造商:WINBOND 制造商全称:Winbond 功能描述:SINGLE-CHIP 1 TO 16 MINUTES DURATION VOICE RECORD/PLAYBACK DEVICES WITH DIGITAL STORAGE CAPABILITY
I5108S 制造商:WINBOND 制造商全称:Winbond 功能描述:SINGLE-CHIP 1 TO 16 MINUTES DURATION VOICE RECORD/PLAYBACK DEVICES WITH DIGITAL STORAGE CAPABILITY
I5108SI 制造商:WINBOND 制造商全称:Winbond 功能描述:SINGLE-CHIP 1 TO 16 MINUTES DURATION VOICE RECORD/PLAYBACK DEVICES WITH DIGITAL STORAGE CAPABILITY
I5108X 制造商:WINBOND 制造商全称:Winbond 功能描述:SINGLE-CHIP 1 TO 16 MINUTES DURATION VOICE RECORD/PLAYBACK DEVICES WITH DIGITAL STORAGE CAPABILITY